Model #10657452700 KENMORE ELITE Side-by-Side Refrigerator

  • Cabinet Parts
    3 Results
  • Refrigerator Liner Parts
    3 Results
  • Air Flow Parts
    3 Results
  • Refrigerator Shelf Parts
    3 Results
  • Freezer Liner Parts
    3 Results
  • Motor And Ice Container Parts
    3 Results
  • Refrigerator Door Parts
    3 Results
  • Freezer Door Parts
    3 Results
  • Dispenser Front Parts
    3 Results
  • Unit Parts
    3 Results
  • Icemaker Parts
    3 Results
  • Control Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Question and Answers

Q:

Kenmore Elite refrigerator now dropping ice from the ice bin

A:

The Refrigerator is one of the most important appliances in the home and by far a must need. So I am understanding your concern over the issue that is currently happening. I have researched your issue on this website and came across a few questions that is similar to yours. The expert provides further detailed information that might enlighten you. Hope this helps!

Read More
Priscilla V -
February 15, 2012
A:

Thank you for your question. I know it can be disappointing when the ice dispenser stops working. This is the advanced dispenser and if the auger motor is not running, it could be due to the motor itself or the board inside the dispenser. Some voltage checks will need to be made to determine, which component has failed. This system uses both ac and dc voltage and a technician may be needed to make these checks. I'm attaching a site you can access, to have a tech come out. Here is a link for the website: Sears Home Services . I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further.

Read More
Scott D -
Sears Technician
February 16, 2012
See more answers
Q:

In 2007 I bought a Sears Kenmore Elite refrig. serial ST4549488 Model 10657452700. Icemaker is not working. Any suggestions other than what booklet suggests?

A:

Having ice for beverages is very important if not then you will have hot drinks, So when an ice maker not working properly it can get very frustrating. While you are waiting on an expert to answer your question, I was searching in the Manage My Life website and found a great link on ice maker not working. I attached the link below. Hope this is useful!

Read More
Dezeray S -
December 07, 2010
A:

I know it's frustrating when the icemaker stops working. The information you have received is good. The icemaker in this model can stop working for a few reasons. Some are listed below:

  • The icemaker itself can fail
  • The water valve may not open
  • The optic boards can fail
  • The fill tube can freeze up
  • Freezer temperature not cold enough
The blinking led light can be flashing a code that will indicate the problem. If it flashes 2 times pauses and continues this while the door is open, it�s normal. Now disconnect power to the refrigerator. To check this icemaker, slide it out, so the front cover can be removed, to access some test terminals. There is a clip located on the back right corner of the icemaker that will need to be removed, to slide the icemaker out. There will be a screw at the bottom of the clip holding it. I�m sending a picture with instructions to remove this clip. With the clip removed, slide the icemaker out and remove the front cover. You will now see the test terminals, which are marked (see picture). Now remove the 3 screws holding the receiver board on the right side and disconnect the harness from the board. Place a jumper between the black and black/white wires (see picture). Now use a second jumper and place it between the L � V terminals on the module. Reconnect the power and with both jumpers in place, water should now flow to the icemaker (be prepared to catch water from the fill tube). If water does flow, the icemaker # 2198597 will need to be replaced. If no water flows but you can hear a humming noise, the water valve # W10159839 will need to be replaced. If nothing at all happens, some voltage checks will need to be made. I hope this will help you.

If you do not feel confident repairing this problem or doing any voltage checks yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services . If you need more assistance additional details will be needed.

Safety Notice: Be sure to disconnect the appliance before performing any troubleshooting procedures. If you are not comfortable with doing any voltage checks or repairs that might be recommended, please contact a local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Scott D -
Sears Technician
December 08, 2010
See more answers

Top Parts