Model #10657033601 KENMORE Side-by-Side Refrigerator

  • Cabinet Parts
    3 Results
  • Refrigerator Liner Parts
    3 Results
  • Refrigerator Shelf Parts
    3 Results
  • Freezer Liner Parts
    3 Results
  • Motor And Ice Container Parts
    3 Results
  • Refrigerator Door Parts
    3 Results
  • Freezer Door Parts
    3 Results
  • Dispenser Front Parts
    3 Results
  • Air Flow Parts
    3 Results
  • Control Parts
    3 Results
  • Unit Parts
    3 Results
  • Icemaker Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

ice chute leak kenmore cold spot 106.57033601 10657069601 Kenmore Side by side refrigerator

Q:

How do I stop my water dispenser from dripping? 10657033601 Kenmore Side by side refrigerator

A:

Thank you for choosing SearsPartsDirect. I will be more than happy to assist you with your Kenmore Refrigerator.

From the information you have provided above, I can understand the frustration of having your refrigerator malfunction, after researching model number 106.57033601. the issue with the dripping seems to be coming from the water inlet valve. When there is a drip coming from the dispenser its due to the water valve not properly closing allowing the water to continue to run. I would suggest replacing the valve to solve the problem. The part number for the W10408179.

I hope you found this information useful. Again thank you for choosing Sears, we appreciate your business, have a great day.

*Safety disclaimer before you try and repair the unit make sure the power supply is disconnected. There may be sharp parts to the unit that can cause injury to you if not careful. If you don’t not feel comfortable checking this yourself you can request a technician by visiting www.SearsHomeService.com*

Read More
Benny23 -
Sears Technician
June 29, 2015
Q:

Can you help me with my ice maker on my side by side?

A:

I see you are having problems with your Ice Maker, I can see how frustrating it maybe. While you are waiting on an expert to answer your question, A suggestion I have is to visit Sears Home Services website to set service with a Sears technician. I attached the link below. Hope this helps! www.searshomeservices.com

Read More
Dezeray S -
October 27, 2010
A:

I'm sorry you are having this problem. The icemaker in this model can stop working for a few reasons. Some are listed below:

  • The icemaker itself can fail
  • The water valve may not open
  • The optic boards can fail
  • The fill tube can freeze up
  • Freezer temperature not cold enough
The blinking led light can be flashing a code that will indicate the problem. If it flashes 2 times pauses and continues this while the door is open, it�s normal. Now disconnect power to the refrigerator. To check this icemaker, slide it out, so the front cover can be removed, to access some test terminals. There is a clip located on the back right corner of the icemaker that will need to be removed, to slide the icemaker out. There will be a screw at the bottom of the clip holding it. I�m sending a picture with instructions to remove this clip. With the clip removed, slide the icemaker out and remove the front cover. You will now see the test terminals, which are marked (see picture). Now remove the 3 screws holding the receiver board on the right side and disconnect the harness from the board. Place a jumper between the black and black/white wires (see picture). Now use a second jumper and place it between the L � V terminals on the module. Reconnect the power and with both jumpers in place, water should now flow to the icemaker (be prepared to catch water from the fill tube). If water does flow, the icemaker # 2198597 will need to be replaced. If no water flows but you can hear a humming noise, the water valve # 4389177 will need to be replaced. If nothing at all happens, some voltage checks will need to be made. These parts are available at SearsPartsDirect .

If you do not feel confident repairing this problem or doing any voltage checks yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services . If you need more assistance additional details will be needed.

Safety Notice: Be sure to disconnect the appliance before performing any troubleshooting procedures. If you are not comfortable with doing any voltage checks or repairs that might be recommended, please contact a local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Scott D -
Sears Technician
October 28, 2010
A:

Scott: Thank you! When I open the door and view the light, I get two flashes a pause and then two more flashes - repeating.. According to your response, that means that part of the ice maker is functioning correctly? Then to narrow the problem, I follow your steps listed above?

Read More
rrtimetables -
October 28, 2010
A:

Yes, so far so good. The flashes indicate the boards are ok. Now follow the steps listed and I hope you find your problem.

Read More
Scott D -
Sears Technician
October 28, 2010
See more answers

Top Parts