Model #10657029601 KENMORE Side-by-Side Refrigerator

  • Cabinet Parts
    3 Results
  • Refrigerator Liner Parts
    3 Results
  • Refrigerator Shelf Parts
    3 Results
  • Freezer Liner Parts
    3 Results
  • Motor And Ice Container Parts
    3 Results
  • Refrigerator Door Parts
    3 Results
  • Freezer Door Parts
    3 Results
  • Dispenser Front Parts
    3 Results
  • Air Flow Parts
    3 Results
  • Control Parts
    3 Results
  • Unit Parts
    3 Results
  • Icemaker Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Is there a replacement part for the unit that houses the door kit assembly? 10657029601 Kenmore Side by side refrigerator

A:

Thank you for choosing Searspartsdirect.com and being a valued member. I can certainly assist you.

If you are referring to key number 1 on the diagram that part is not servicable. You would have to purchase the entire door in order to replace the dispenser housing.

 You can also visit searpartsdirect.com for parts, diagrams, and repair information.

 

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day. 

Read More
Natasha12 -
Sears Technician
August 04, 2015
A:
Natasha12 -
Sears Technician
August 04, 2015
See more answers
Q:

Ice Maker Not Working...

A:

Thank you for your question. I know it can be disappointing when the icemaker stops working. The icemaker in this model can stop working for a few reasons. Some are listed below:*The icemaker itself can fail.*The water valve may not open.*The optic boards can fail.*The fill tube can freeze up.*Freezer temperature not cold enough (should be 0 – 5 degrees).The blinking led light can be flashing a code that will indicate the problem. If it flashes 2 times pauses and continues this while the door is open, it will be normal and if it stays on continuous, when the flapper door on the left side is held in, it indicates the boards are ok. When checking this icemaker, tape the little flapper door shut and disconnect power to the refrigerator. To check this icemaker, slide it out, so the front cover can be removed, to access some test terminals. There is a clip located on the back right corner of the icemaker that will need to be removed, to slide the icemaker out. There will be a screw at the bottom of the clip holding it. I’m sending a picture with instructions to remove this clip. With the clip removed, slide the icemaker out and remove the front cover. You will now see the test terminals, which are marked (see picture). Now remove the 3 screws holding the receiver board on the right side pull the board out and disconnect the harness from the board. Place a jumper between the black and black/white wires (see picture). Now use a second jumper and place it between the L – V terminals on the module. Reconnect the power and with both jumpers in place, water should now flow to the icemaker (be prepared to catch water from the fill tube). If water does flow, the icemaker will need to be replaced. If no water flows but you can hear a humming noise, the water valve will need to be replaced. If nothing at all happens, some voltage checks will need to be made. I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further.   If you do not feel confident repairing this problem or doing any voltage checks yourself, then you can have it repaired at your home by a Sears's technician. Here is a link for the website: Sears Home Services.    _Safety Notice_: Be sure to disconnect the appliance before performing any troubleshooting procedures. If you are not comfortable with doing any voltage checks or repairs that might be recommended, please contact a local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others. 

Read More
Scott D -
Sears Technician
November 27, 2013
Q:

Ice maker stopped working 10657029601 Kenmore Side by side refrigerator

A:

I know that it can be very frustrating to have issues with your ice maker. First, check to see if the temperature is cold enough to cycle the icemaker (below 12 degrees). To check the temperature, place a thermometer between some packages. Air temperature is not a good check. If the temperature is ok and there is ice in the mold of the icemaker, it will indicate the thermostat inside the icemaker has failed. Check the ice maker fill tube to make sure its not frozen over. If it is defrost it with a hair dryer. If the tube continues to freeze then I recommend purchasing a heater kit for the fill tube. If this all checks out okay, then the image below will instruct you on how to test the ice maker. If the unit fills and cycles, then the water valve will need to be replaced. If the unit does not fill and cycle, then the ice maker will need to be replaced. If you don't feel comfortable doing this yourself, please click on this link to schedule service: Sears Home Services. Click on "Get Started" and follow the directions, click on the red "NEXT" button to continue. I hope this helps. Please feel free to let me know if you need further assistance. We are always here to help. Thank you for using Manage My Life.com.

Read More
AnneJ -
Sears Technician
September 18, 2013

Top Parts