Model #10657029600 KENMORE Side-by-Side Refrigerator

  • Cabinet Parts
    3 Results
  • Refrigerator Liner Parts
    3 Results
  • Refrigerator Shelf Parts
    3 Results
  • Freezer Liner Parts
    3 Results
  • Motor And Ice Container Parts
    3 Results
  • Refrigerator Door Parts
    3 Results
  • Freezer Door Parts
    3 Results
  • Dispenser Front Parts
    3 Results
  • Air Flow Parts
    3 Results
  • Control Parts
    3 Results
  • Unit Parts
    3 Results
  • Icemaker Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

kenmore refrigerator 10657029600 only work on high setting

A:

When a Kenmore Refrigerator is not functioning properly, it is a cause for concern. Managemylife.com is a place to go for troubleshooting problems with refrigerators. I researched managemylife.com and I am providing links that may help with the cooling on your refrigerator, while you wait for an expert answer.

Read More
Anna T -
March 06, 2012
A:

Thank you for your question. I can understand your concern about the control setting. If it only runs when set to the coldest setting, it indicates the thermostat is out of calibration. In this case, the thermostat # 2315562 would need to be replaced. It's available at SearsPartsDirect . I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further.

Read More
Scott D -
Sears Technician
March 08, 2012
See more answers
Q:

Ice Maker does not work

A:

I understand that your ice maker is not properly working. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question. Have a great day!

Read More
Alina F. -
February 24, 2012
A:

Thank you for your question. I know it can be disappointing when the icemaker stops working. I suspect since this problem occurred after a power failure, that the optic boards # 4389102 may be defective now. However, here is more information about this type of icemaker. The icemaker in this model can stop working for a few reasons. Some are listed below:

  • The icemaker itself can fail
  • The water valve may not open
  • The optic boards can fail
  • The fill tube can freeze up
  • Freezer temperature not cold enough (should be 0 � 5 degrees)
The blinking led light can be flashing a code that will indicate the problem. If it flashes 2 times pauses and continues this while the door is open, it will be normal and if it stays on continuous, when the flapper door on the left side is held in, it indicates the boards are ok. I�m attaching a chart for the led indicator. Now disconnect power to the refrigerator. To check this icemaker, slide it out, so the front cover can be removed, to access some test terminals. There is a clip located on the back right corner of the icemaker that will need to be removed, to slide the icemaker out. There will be a screw at the bottom of the clip holding it. I�m sending a picture with instructions to remove this clip. With the clip removed, slide the icemaker out and remove the front cover. You will now see the test terminals, which are marked (see picture). Now remove the 3 screws holding the receiver board on the right side pull the board out and disconnect the harness from the board. Place a jumper between the black and black/white wires (see picture). Now use a second jumper and place it between the L � V terminals on the module. Reconnect the power and with both jumpers in place, water should now flow to the icemaker (be prepared to catch water from the fill tube). If water does flow, the icemaker # 2198597 will need to be replaced. If no water flows but you can hear a humming noise, the water valve # W10408179 will need to be replaced. If nothing at all happens, some voltage checks will need to be made. I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further.

If you do not feel confident repairing this problem or doing any voltage checks yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services . If you need more assistance additional details will be helpful.

Safety Notice: Be sure to disconnect the appliance before performing any troubleshooting procedures. If you are not comfortable with doing any voltage checks or repairs that might be recommended, please contact a local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Scott D -
Sears Technician
February 25, 2012
See more answers
Q:

How do I remove the handles from my Kenmore refrigerator?

A:

In order to remove the door handle, grasp the door handle with both hands & force upwards to disengage it from the holding clips. The holding clips are what is usually loose. Tighten as needed.

Read More
biker dave -
Sears Technician
September 05, 2008

Top Parts