Model #10657022600 KENMORE Side-by-Side Refrigerator

  • Cabinet Parts
    3 Results
  • Refrigerator Liner Parts
    3 Results
  • Refrigerator Shelf Parts
    3 Results
  • Freezer Liner Parts
    3 Results
  • Motor And Ice Container Parts
    3 Results
  • Refrigerator Door Parts
    3 Results
  • Freezer Door Parts
    3 Results
  • Dispenser Front Parts
    3 Results
  • Air Flow Parts
    3 Results
  • Control Parts
    3 Results
  • Unit Parts
    3 Results
  • Icemaker Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

My Kenmore #10657022600 is not making ice.

A:

I am sorry that you are having some difficulties with your ice maker and I will be happy to help. I did some research and I was able to find a link with a similar question. I am also adding a second link in where you can set service to have your ice maker repaired by a certified technician. I hope this helps with your ice maker troubles while you wait for your expert response.

Read More
Joseph P. -
October 30, 2012
A:

I know that it can be very frustrating to have your ice maker stop working. What we usually find in this type of situation is a frozen fill tube. Directly above the icemaker fill funnel you will see a hose coming from the ceiling of the freezer, if this hose is frozen solid, you will need to have the water valve replaced & the fill tube defrosted. The best way to defrost the fill tube is to turn the refrigerator off for at least 24 hours. If this does not work, then the problem is with either the water valve or the ice maker itself. You will need to perform a test to determine which is causing it. Let the ice maker cycle by jumping T to H momentarily, when you remove the insulated jumper, the motor will continue to cycle. Wait with your meter ready at the water valve until the ice module calls for water, this should be less than 2 minutes, unless you have ice being ejected. If you have the correct voltage, I would recommend replacing the water valve. If you have anything below 110 volts I would recommend replacing the ice maker module. If you don't feel comfortable doing this yourself, just click on this link to schedule service: Sears Home Services . I hope this helps. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
October 31, 2012
See more answers
Q:

My fridge side keeps getting Warm

A:

fan or the defrost timer

Read More
Mercy -
August 24, 2012
A:

I can understand how difficult it can be to have you refrigerator stop working properly. The problem that you are having is the drain system is freezing up. This will cause an ice blockage that prevents cold air from circulating into the refrigerator. Every time the unit goes into a defrost cycle, water will run down into the refrigerator, instead of down the drain. To clear the drain, remove everything in the freezer so the back panel can be removed. With the panel removed, you will see the evaporator coil and directly under the coil is the drain trough (pan). The trough will probably be full of ice that will need to be removed. With the ice out of the trough, you will be able to see the drain hole which will be plugged with ice. Use hot water to clear the drain hole. Keep working the hot water into the hole and wiping the excess water. This can take quite awhile depending on how deep the ice is. This will need to be done until you get a good water flow down to the bottom drain pan. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
August 24, 2012
See more answers
Q:

Refrigerator's ice maker

A:

It is great to have ice available on demand. I can appreciate you wanting to figure this problem out. While you wait for the expert, you can check a previous expert post for possible causes if you like. Bear in mind the model does not match yours. I also added the owner's manual. I see it has some good troubleshooting tips that may help. I attached the links below.

Read More
Barbara H. -
February 24, 2011
A:

The problem could be with the freezer door switch not closing to the dispenser when the door is closed, the led display in the dispenser front panel, or a wire burned or broken inside the dispenser area.

The answer Joseph P sent has some good suggestions in it.

To remove the front panel on the dispenser, place a screwdriver in the 2 small notches on the bottom edge of the dispenser front trim one notch at a time. Pry out on the dispenser front panel and it will move out. Pull the bottom of the panel away from the freezer door about 2 inches and lift it up. This will allow you to access the parts inside the dispenser.

Be sure to disconnect the power to the refrigerator before removing any parts.

You can remove the freezer light switch by inserting a small screwdriver between the switch and the refrigerator cabinet and gently prying the edges out. Put a cloth between the screwdriver and the cabinet to prevent scratching the cabinet.

If you have more questions, reply on this thread and I will be glad to help.

Read More
Jimmy K -
Sears Technician
February 26, 2011
See more answers

Top Parts