Model #10656823600 KENMORE Side-by-Side Refrigerator

  • Cabinet Parts
    3 Results
  • Refrigerator Liner Parts
    3 Results
  • Refrigerator Shelf Parts
    3 Results
  • Freezer Liner Parts
    3 Results
  • Motor And Ice Container Parts
    3 Results
  • Refrigerator Door Parts
    3 Results
  • Freezer Door Parts
    3 Results
  • Dispenser Front Parts
    3 Results
  • Air Flow Parts
    3 Results
  • Control Parts
    3 Results
  • Unit Parts
    3 Results
  • Icemaker Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kenmore Side By Side Refrigerator Model 106.56823600

A:

Having frost buildup in the freezer can be inconvenient and cause some water damage so I will be happy to help. While you are waiting for your expert answer, I did manage to find a link that will provide you with some good tips to help you with your freezer problem. I hope my link is useful.

Read More
celene -
September 26, 2011
A:

Thank you for your question. I can understand your concern about this icing condition. This appears to be a dual problem. The ice build up on the freezer floor will be caused by a frozen drain. To clear the drain, remove everything in the lower section of the freezer, so the back panel (# 17 in picture) can be removed. With the panel removed, you will see the evaporator coil and directly under the coil is the drain trough (pan). The trough will probably be full of ice that will need to be removed. A hair dryer works well for this. Just be careful not to get it too hot. With the ice out of the trough, you will be able to see the drain hole, which will be plugged with ice. Use hot water to clear the drain hole. Keep working the hot water into the hole and wiping the excess water. This can take quite awhile, depending on how deep the ice is. This will need to be done until you get a good water flow down to the bottom drain pan.

The hard freezing and condensation on the center wall can be due the freezer getting excessively cold (below zero degrees). To check the temperature, place a thermometer between some packages. Air temperature is not a good check. If it is too cold, usually adjusting the cold control to a warmer setting, will correct this problem. I hope this will help you. If you would like more assistance, reply this thread and I will be glad to assist you further.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Scott D -
Sears Technician
September 29, 2011
See more answers
Q:

kenmore side by side fridge

A:

ManageMyLife.com is a great place to find the answers to just about anything, especially on appliances. I would suggest that you provide the model # so your expert will be able to provide you the best possible answer. Just click on reply below and the provide the required data.

Read More
Priscilla V -
September 19, 2011
A:

oh...sorry model #10656823600 thanks

Read More
michelle -
September 20, 2011
A:

Thank you for your question. I can understand your concern. If frost is building up now, it indicates a problem with the defrost system. As the frost gets thicker, it reduces the air flow to the fridge section causing it to get warmer. Power outages can damage electronic controls and the electronic defrost control has probably failed now. A good check for this will be to do the following in the order listed.

  1. Unplug the power cord
  2. Turn the thermostat to the off position and leave it off
  3. Plug the power cord back in
After a few minutes, open the freezer door and listen for a sizzling sound. If you can hear this sound, it indicates the heating element is on. This will mean the defrost control # 4388932 is not advancing now and will need to be replaced. It's available at SearsPartsDirect . If nothing happens, some voltage checks will need to be made. I recommend having a technician make these checks. However, if you have a meter and feel confident that you can safely make these checks, reply to this thread and I will be glad to assist you further. I hope this will help you.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Scott D -
Sears Technician
September 21, 2011
See more answers
Q:

kenmore refrigerator model # 10656823600

A:

Doors of all kinds often end up sagging a bit. I found some general advice from a previous expert post that may help while you wait for the expert to review your model. I attached the link below. Hope this helps get the fridge door level.

Read More
Barbara H. -
January 09, 2011
A:

I understand your concern about the doors. It's not unusual for the doors not to line up exactly. Depending on the weight, if the door has a heavy load, it could be normal. The information you have received is correct. Leveling the cabinet in most cases, will adjust the doors and usually helps line them up. There is a shim kit # 4387828 available, to help level the cabinet. The clicking noise you hear will be from the door closer. Adding some silicone grease # 542638 to the closer, will help stop this noise. The closer is located on the bottom door hinge, between the door and the hinge. The parts listed are available at SearsPartsDirect . I hope this will help you. If you would like more assistance, any additional details will be helpful and I will be glad to assist you further.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Scott D -
Sears Technician
January 11, 2011
See more answers

Top Parts