Model #10656673500 KENMORE Side-by-Side Refrigerator

  • Cabinet Parts
    3 Results
  • Refrigerator Liner Parts
    3 Results
  • Refrigerator Shelf Parts
    3 Results
  • Freezer Liner Parts
    3 Results
  • Motor And Ice Container Parts
    3 Results
  • Refrigerator Door Parts
    3 Results
  • Freezer Door Parts
    3 Results
  • Dispenser Front Parts
    3 Results
  • Air Flow Parts
    3 Results
  • Control Parts
    3 Results
  • Unit Parts
    3 Results
  • Icemaker Parts, Optional Parts
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Ice maker working sporadically 10656673500 Kenmore Side by side refrigerator

A:

Thank You for choosing Sears PartsDirect.com and being a valued member. It is unfortunate to hear that you are having issues with your refrigerator and I do understand your frustration. Glad to help out. I'm looking at your model number 10656673500 and here is a link that may help troubleshoot the problem. From your description I would suspect an issue with the valve not filling the tray properly. Just click the blue link above to be taken to the page. I trust this information will help you.

 

Thank you for choosing Sears PartsDirect.com.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Sherman_G_Wallace -
Sears Technician
December 24, 2014
A:

Thanks, but that link just goes to some YouTube videos. My icemaker fills fine, it just is slow dumping the ice. There is currently ice in the mold, it just doesn't want to dump and complete the cycle. The funny thing is, occasionally it will. Thanks for your help.

Read More
Dawn -
December 24, 2014
See more answers
Q:

How can I restart the icemaker after suddenly not working?

A:

A ice maker is just one of those things we depend on, and when it stops working it can definitely be a inconvenience. I have provided you a couple links below to Manage my life that are very helpful for you. Hope this helps!

Read More
Maira E -
October 08, 2010
A:

The icemaker in this model can stop working for a few reasons. Some are listed below:

  • The icemaker itself can fail
  • The water valve may not open
  • The optic boards can fail
  • The fill tube can freeze up
  • Freezer temperature not cold enough
The blinking led light can be flashing a code that will indicate the problem. If it flashes 2 times pauses and continues this while the door is open, it’s normal. Now disconnect power to the refrigerator. To check this icemaker, slide it out, so the front cover can be removed, to access some test terminals. There is a clip located on the back right corner of the icemaker that will need to be removed, to slide the icemaker out. There will be a screw at the bottom of the clip holding it. I’m sending a picture with instructions to remove this clip. With the clip removed, slide the icemaker out and remove the front cover. You will now see the test terminals, which are marked (see picture). Now remove the 3 screws holding the receiver board on the right side and disconnect the harness from the board. Place a jumper between the black and black/white wires (see picture). Now use a second jumper and place it between the L – V terminals on the module. Reconnect the power and with both jumpers in place, water should now flow to the icemaker (be prepared to catch water from the fill tube). If water does flow, the icemaker # 2198678 will need to be replaced. If no water flows but you can hear a humming noise, the water valve # 4389177 will need to be replaced. If nothing at all happens, some voltage checks will need to be made.

If you do not feel confident repairing this problem or doing any voltage checks yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services . If you need more assistance additional details will be needed.

Safety Notice: Be sure to disconnect the appliance before performing any troubleshooting procedures. If you are not comfortable with doing any voltage checks or repairs that might be recommended, please contact a local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Scott D -
Sears Technician
October 09, 2010
A:

Are these the same instruction to check the ice maker for model #10656672500? If so can you send me a picture of the location for the test terminals?

Read More
Anonymous -
July 09, 2011
A:

Yes, the instructions will be the same for this model. The test terminals will be behind the icemaker cover. Pull the front cover off and you will see the test terminals. I'm attaching a picture of the test terminals. I hope this will help you. If you would like more assistance, any additional details will be helpful.

Read More
Scott D -
Sears Technician
July 11, 2011
A:

Could you please sent me the same diagram info. I also have the#10656672500 and icemaker stopped working after it was turned off for a week.

Read More
Tony -
November 28, 2012
A:

Tony, it will be the same information as what is listed above but the icemaker for this unit is # 2198597 and the water valve is # W10408179. I hope this will help you.

Read More
Scott D -
Sears Technician
November 29, 2012
See more answers
Q:

Why won't this new water filter snap into place?

A:

There have not been any problems with this filter pushing back in place. Make sure it's in the proper position when reinserting it. You may have to push harder to get it to snap. If you decide to replace the housing, the hoses are not hard to remove and reinstall. I'm attaching some pictures and instructions on this type of fitting. There will be some water leakage when these hoses are removed. I hope this will help you. If you need more assistance, please resubmit your question with more details.

Read More
Scott D -
Sears Technician
January 21, 2010
A:

Thanks Scott. After downloading a manual I tried a different filter and it snapped into place. I appreciate your help.

Read More
Sonny -
September 10, 2012
See more answers

Top Parts