Model #10656232400 KENMORE Side-by-Side Refrigerator

  • Cabinet Parts
    3 Results
  • Refrigerator Liner Parts
    3 Results
  • Refrigerator Shelf Parts
    3 Results
  • Freezer Liner Parts
    3 Results
  • Motor And Ice Container Parts
    3 Results
  • Refrigerator Door Parts
    3 Results
  • Freezer Door Parts
    3 Results
  • Dispenser Front Parts
    3 Results
  • Air Flow Parts
    3 Results
  • Control Parts
    3 Results
  • Unit Parts
    3 Results
  • Icemaker Parts, Parts Not Illustrated
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

What is the cubic feet of my Kenmore Side by Side? 106.56232400? 10656232400 Kenmore Refrigerator, sxs

A:

Thanks for the inquiry and for being a valued member.

This Kenmore model of refrigerator features 22 cu./ft. of capacity.

I hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
August 11, 2015
A:

Could you please break this down by freezer and refrig

Read More
Eldon Spady -
October 21, 2015
See more answers
Q:

my fan or compressor runs constantly in freezer 10656232400 Kenmore Refrigerator, sxs

A:

Thank you for contacting SearsPartsDirect.com with your question about your Kenmore refrigerator. I am so sorry you are having a problem with it. The compressor or fan running constantly will not only drive up your electric bill, but will also cause the refrigerator to fail prematurely. I will be happy to helpy you with this. 
 
The most likely reason your freezer is very cold and the compressor is constantly running is you have the temperature control set too low. The factory settings for both the refrigerator and freezer sections are 4. They should only be adjusted if the unit isn't cool enough or is getting too cold. To keep food properly cooled in the freezer section, the temperature should be between -5 degrees to +5 degrees Fahrenheit. Keeping the freezer any colder than that overworks the compressor. 
 
The owner's manual for your model is not online, but I located a similar model that uses the same digital control setup. I have included the link for you to view that manual online. 
 
 
The instructions for resetting the controls is on page 10. Keep in mind that it will take about 24 hours for the freezer to adjust to the new setting. It may take a couple of trys until you get it to the right range where it is keeping the food frozen without keeping it colder than it needs to be. 
 
I hope this answers your question. If you need further assistance, please resubmit your question with additional details. Thank you for choosing Sears, we appreciate your business. 

Read More
Rachel Morgan -
Sears Technician
April 05, 2014
Q:

Refrigerator 10656232400 Ice Maker flashing red light

A:

Thank you for your question. I know it can be disappointing when the icemaker stops working. The icemaker in this model can stop working for a few reasons. Some are listed below:*The icemaker itself can fail.*The water valve may not open.*The optic boards can fail.*The fill tube can freeze up.*Freezer temperature not cold enough (should be 0 – 5 degrees).The blinking led light can be flashing a code that will indicate the problem. If it flashes 2 times pauses and continues this while the door is open, it will be normal and if it stays on continuous, when the flapper door on the left side is held in, it indicates the boards are ok. When checking this icemaker, tape the little flapper door shut and disconnect power to the refrigerator. To check this icemaker, slide it out, so the front cover can be removed, to access some test terminals. There is a clip located on the back right corner of the icemaker that will need to be removed, to slide the icemaker out. There will be a screw at the bottom of the clip holding it. With the clip removed, slide the icemaker out and remove the front cover. You will now see the test terminals, which are marked. Now remove the 3 screws holding the receiver board on the right side pull the board out and disconnect the harness from the board. Place a jumper between the black and black/white wires. Now use a second jumper and place it between the L – V terminals on the module. Reconnect the power and with both jumpers in place, water should now flow to the icemaker (be prepared to catch water from the fill tube). If water does flow, the icemaker # W10190961 will need to be replaced. If no water flows but you can hear a humming noise, the water valve # W10408180 will need to be replaced. If nothing at all happens, some voltage checks will need to be made. I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further.   If you do not feel confident repairing this problem or doing any voltage checks yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website:  Sears Home Services  _Safety Notice_: Be sure to disconnect the appliance before performing any troubleshooting procedures. If you are not comfortable with doing any voltage checks or repairs that might be recommended, please contact a local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.  

Read More
Scott D -
Sears Technician
December 02, 2013

Top Parts