Model #10655604400 KENMORE ELITE Side-by-Side Refrigerator

  • Cabinet Parts
    3 Results
  • Refrigerator Liner Parts
    3 Results
  • Refrigerator Shelf Parts
    3 Results
  • Freezer Liner Parts
    3 Results
  • Motor And Ice Container Parts
    3 Results
  • Refrigerator Door Parts
    3 Results
  • Freezer Door Parts
    3 Results
  • Dispenser Front Parts
    3 Results
  • Air Flow Parts
    3 Results
  • Control Parts
    3 Results
  • Unit Parts
    3 Results
  • Icemaker Parts, Optional Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

How often should it go thru a defrost cycle and what failure will stop both ice production and defrost cycling? 10655604400 Kenmore Elite Refrigerator

A:

Thanks for your question- we see that no one from the community responded.  If you still require assistance on this topic, please resubmit your question with any updated information and we will have one of our experts take a look.  Also, we have updated our site to include information regarding common repairs and diagnosis, which can be found here: www.searspartsdirect.com/repair-help.html.  If you are looking for your owner’s manual, it can be found here: http://www.searspartsdirect.com/partsdirect/user-manuals.  Thanks for visiting SearsPartsDirect.com.

Read More
Natasha12 -
Sears Technician
May 13, 2014
Q:

My water dispencer on my Refer #106.5560400 will not stop dripping. I tryed clearing the line and it still drips. What can the problem be? 106.5560400

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when there is problems with the refrigerator.
 
Glad to help out.   Im  looking at your Kenmore Refrigerator model number10655604400.

Thank you for choosing SearsPartsDirect.com. I understand how frustrating it can be when the dispenser continuously drips. I have included instructions below on how to replace the water valve in the refrigerator.  It sounds like that is the problem.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

1. Pull the refrigerator away from the wall so that the rear is accessible.

2. Unplug the power cord from the wall outlet and turn off the water supply valve by turning the handle clockwise until it is tight.

3. Remove the water supply line from the water inlet valve using an adjustable wrench. Place a towel below the valve to catch any water remaining in the line.

4. Remove the lower access panel of the refrigerator by removing the screws securing it in place.

5. Remove the mounting screws securing the inlet valve to the refrigerator cabinet.

6. Transfer the solenoid wire connectors from the old inlet valve to the new inlet valve.

7. Press each quick-connector on the bottom of the inlet valve, at the point at which the each tube enters the inlet valve using an open-ended wrench. Measure 11/16 of an inch from the end of the tube and make a mark using a marker. Insert the tube into the same tube inlet on the new inlet valve up to the mark. Repeat for each tube.

8. Secure the new inlet valve the to refrigerator cabinet using the mounting screw removed from the old valve.

9. Replace the lower access panel of the refrigerator.

10. Connect the water supply line to the new inlet valve. Tighten the compression nut using and adjustable wrench.

11. Turn on the water supply valve and examine the connection for any leaks. Tighten as necessary.

12. Plug the refrigerator's power cord back into the wall outlet and then push the refrigerator back against the wall.

13. Run approximately one gallon of water through the water fountain to clear air from the tubes.

Water valve for the model 10655604400.


Please "RESUBMIT YOUR QUESTIONS IF THERE IS ANY OTHER PROBLEMS".
 
Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs.  Thank you for choosing Sears and using our SearsPartsDirect.com.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: www.SearsServiceCrew.com
 

Read More
Larry L -
Sears Technician
April 23, 2014
Q:

Why does the water dispenser work but no water flow to the ice maker?

A:

Maybe the ice maker is not even cycling. This could be a problem with the ice maker, the water valve or the optic boards. If the ice maker doesn't cycle the relay in the receiver board may not be closing thus no voltage would be getting to the ice maker. The ice maker module may be defective also, not allowing it to cycle. The ice maker may be cycling ok but the water valve could be defective and not allowing any water flow. A technician will have the equipment to check this. If you need more assistance you can resubmit your question with more details.

Read More
Scott D -
Sears Technician
A:

the replacement part that was suggested seems to "push" the water into the top of the 'fridge where the ice maker is located.the problem is the water is not going out of the replacement part ...how can I tell if the replacement part (#1) is good and working and (#2) is the right replacement part because it looks similar but not exactly the same ..the fridge is at least 10 years old or more I believe

Read More
EqualizerAl -
September 07, 2010
A:

Contrary to the indication of "2 responses" or "expert answered", there are no responses or answers visible here.

Read More
Dennis -
March 08, 2014
See more answers

Top Parts