Model #10655529400 KENMORE Side-by-Side Refrigerator

  • Cabinet Parts
    3 Results
  • Refrigerator Liner Parts
    3 Results
  • Refrigerator Shelf Parts
    3 Results
  • Freezer Liner Parts
    3 Results
  • Motor And Ice Container Parts
    3 Results
  • Refrigerator Door Parts
    3 Results
  • Freezer Door Parts
    3 Results
  • Dispenser Front Parts
    3 Results
  • Air Flow Parts
    3 Results
  • Control Parts
    3 Results
  • Unit Parts
    3 Results
  • Icemaker Parts, Parts Not Illustrated
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

My ice maker is not working properly

A:

It's great to have ice for drinks readily available, but when the ice maker isn't working properly it can frustrating. I am providing a link on a similar issue which may be helpful while an expert responds to your specific model.

Read More
Anna T -
September 26, 2012
A:

Thank you for your question. I know it can be disappointing when the icemaker stops working. The icemaker in this model can stop working for a few reasons. Some are listed below:

  • The icemaker itself can fail
  • The water valve may not open
  • The optic boards can fail
  • The fill tube can freeze up
  • Freezer temperature not cold enough (should be 0 � 5 degrees)
The blinking led light can be flashing a code that will indicate the problem. If it flashes 2 times pauses and continues this while the door is open, it will be normal and if it stays on continuous, when the flapper door on the left side is held in, it indicates the boards are ok. I�m attaching a chart for the led indicator. When checking this icemaker, tape the little flapper door shut and disconnect power to the refrigerator. To check this icemaker, slide it out, so the front cover can be removed, to access some test terminals. There is a clip located on the back right corner of the icemaker that will need to be removed, to slide the icemaker out. There will be a screw at the bottom of the clip holding it. I�m sending a picture with instructions to remove this clip. With the clip removed, slide the icemaker out and remove the front cover. You will now see the test terminals, which are marked (see picture). Now remove the 3 screws holding the receiver board on the right side pull the board out and disconnect the harness from the board. Place a jumper between the black and black/white wires (see picture). Now use a second jumper and place it between the L � V terminals on the module. Reconnect the power and with both jumpers in place, water should now flow to the icemaker (be prepared to catch water from the fill tube). If water does flow, the icemaker # 2198597 will need to be replaced. If no water flows but you can hear a humming noise, the water valve # 4389177 will need to be replaced. If nothing at all happens, some voltage checks will need to be made. I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further.

If you do not feel confident repairing this problem or doing any voltage checks yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services . If you need more assistance additional details will be helpful.

Safety Notice: Be sure to disconnect the appliance before performing any troubleshooting procedures. If you are not comfortable with doing any voltage checks or repairs that might be recommended, please contact a local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Scott D -
Sears Technician
September 28, 2012
A:

My side by side MD # 106.55529400 ice maker is not working no water in maker. The drinking water in door is working but not ice maker getting any water. The red light on switch is blinking twice then pause and then when you push flapper on left side it is on continues Can you help Dave

Read More
Dave -
August 11, 2015
See more answers
Q:

Refrigerator not cold 10655529400 Kenmore Refrigerator, sxs

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your refrigerator. Upon researching model 10655529400; it sounds like the damper assembly may need to be replaced. The damper assembly allows the cold air from the freezer side to enter the refrigerator section by opening a vent between the two compartments. Once the refrigerator section reaches the temperature it is set to the damper will close the vent between the two compartments not allowing the cold air to enter the refrigerator section until more cold air is needed. So when the damper fails the damper vent can stay stuck in the open position causing the refrigerator section to get too cold and freeze the food inside. I have posted a link of the damper to view the link click here.

I trust this information will help you, we appreciate your business thank for choosing Sears.

Read More
CarlosZ -
Sears Technician
August 04, 2015
Q:

106.55529400 refrigerator icing over and leaking out front door 106.55529400

A:

Thank you for choosing SearsPartsDirect.com. I will be more than happy to assist you. I can understand any frustration you may have experienced with regards to your unit. Let’s see what we can do for you.

It sounds like there could be some sort of food debris stuck in the drain hole. I would recommend defrosting that area where the drain tube is and make sure there is no clog.

Hope this information has helped you. If you are not comfortable doing this repair you can click here to schedule a technician or call toll free 1-800-469-4663. Again, thank you for choosing SearsPartsDirect.com.

 

Read More
JeffwallaceIII -
Sears Technician
July 27, 2015

Top Parts