Model #10654612300 KENMORE Side-by-Side Refrigerator

  • Cabinet Parts
    3 Results
  • Refrigerator Liner Parts
    3 Results
  • Refrigerator Shelf Parts
    3 Results
  • Freezer Liner Parts
    3 Results
  • Motor And Ice Container Parts
    3 Results
  • Refrigerator Door Parts
    3 Results
  • Freezer Door Parts
    3 Results
  • Dispenser Front Parts
    3 Results
  • Air Flow Parts
    3 Results
  • Control Parts
    3 Results
  • Unit Parts
    3 Results
  • Icemaker Parts, Parts Not Illustrated
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Digital Control Panel failing 10654612300 Kenmore Refrigerator

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your refrigerator. Upon researching model 10654612300; it sounds like the control board may need to be replaced. The control board governs the functions of the refrigerator so when it fails the refrigerator will start working out of its normal order and can even affect the temperatures in the unit. 

I trust this information will help you, we appreciate your business thank for choosing Sears.

Read More
CarlosZ -
Sears Technician
March 03, 2015
Q:

Refrigerator compressor not starting

A:

When the refrigerator stops working it does require immediate attention. I see you have already begun tests. I located a similar question for this model that may help while you wait for the expert to respond. I attached the link below. I hope this helps.

Read More
Barbara H. -
February 05, 2012
A:

Thank you for your question. I'm sorry you are having this problem with the refrigerator. The resistance readings on the compressor windings are good. If the condenser fan motor is running, it means the compressor should also have voltage to it because both components are on the same circuit (see image). If you replaced the starting device, which is the relay and overload combination # 2319792 and the compressor still won't start, it will lead to a locked compressor. In this case, the compressor will need to be replaced. A technician will be required to make this type of repair. I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further.

Read More
Scott D -
Sears Technician
February 07, 2012
See more answers
Q:

What part do I need to fix my refrigerator?

A:

This type of problem will either be with the control board or the thermistor (sensor). The only way to determine between the two would be, to make some resistance checks, on the thermistor. To make these checks, the thermistor inside the freezer section, will need to be disconnected. I'm sending some pictures and instructions of how to access the freezer thermistor. It's located next to the air baffle assembly going into the refrigerator. First disconnect power to the refrigerator before accessing the thermistor. I'm also sending a resistance chart at different temperatures for the thermistor. The best check is, to actually remove the thermistor and place it in a glass of ice water, which is 32 degrees. At this temperature, the resistance should be approx. 8500 ohms. If the thermistor # 2188819 resistance check is ok, then the main board # 82021528 will need to be replaced. Both of these parts are available at SearsPartsDirect . If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Safety Notice: Be sure to disconnect the appliance before performing any troubleshooting procedures. If you are not comfortable with doing any voltage checks or repairs that might be recommended, please contact a local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Scott D -
Sears Technician
March 15, 2010

Top Parts