Model #10654599400 KENMORE Side-by-Side Refrigerator

  • Cabinet Parts
    3 Results
  • Refrigerator Liner Parts
    3 Results
  • Freezer Liner Parts
    3 Results
  • Motor And Ice Container Parts
    3 Results
  • Refrigerator Door Parts
    3 Results
  • Freezer Door Parts
    3 Results
  • Dispenser Front Parts
    3 Results
  • Air Flow Parts
    3 Results
  • Control Parts
    3 Results
  • Unit Parts
    3 Results
  • Icemaker Parts, Optional Parts
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

my 106.54599400 fridge has stopped making ice and now it seems the freezer is too warm (soft ice cream). 10654599400 Kenmore Refrigerator

A:

Thank You for choosing Sears PartsDirect.com and being a valued member. It is unfortunate to hear that you are having issues with your washer and I do understand your frustration. Glad to help out. I'm looking at your model number 10654599400 and based on your description I would suggest checking the door seals closely top to bottom for proper seating to cabinet. If the unit is running all the time then it is most likely not a defrost problem because the unit shuts down during defrost, the control would also shut the condenser unit down if it were the problem you should notice short run times of the compressor. Your description of only 1/4 of the evaporator coil being frosted is most concerning and would indicate a refrigerant flow issue within the sealed system.(When checking the evaporator coil be sure the unit has been running for a couple hours.) If there is a sealed system issue, then a certified technician needs to inspect this refrigerator. It first needs to be determined if the compressor is running. It is normal for the compressor to get hot. If it's not running, the problem could be with the start device on the compressor or the compressor itself. If it is running, the problem will be in the seal system. It could be a low charge, a restriction or the compressor may not be pumping properly. Here is a link that may help with additional troubleshooting. Just click the blue link above to be taken to the page. I trust this information will help you.

 

Thank you for choosing Sears PartsDirect.com.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

 

Read More
Sherman_G_Wallace -
Sears Technician
December 23, 2014
Q:

Refrigerator is not staying cold, freezer works fine 10654599400

A:

Thank you for your question.  Your symptom indicates a sealed system failure. The sealed system could have developed a small leak and the system is too low of coolant this would cause the walls of the freezer to have frost.  The compressor could be at fault too, in not pumping correctly. This type of failure will require a service technician in order to diagnose the exact failure. If the leak is found to be somewhere in the inner walls of the freezer where the evaporator tubing is routed, the leak can not be repaired. You would have to replace the freezer. Now, if the leak is found somewhere outside the freezer walls like at one of the compressor fittings or somewhere on the condenser coils, it can likely be repaired but would be expensive and not worth repairing.

 

Have more questions please reply to this post.

Thank you for choosing Manage My Life.

Read More
dtova00 -
Sears Technician
September 15, 2013
Q:

Kenmore refrigerator Model 106.45499400 Ice Maker Not working

A:

The ice maker not working can be frustrating. I found some information for you that I am hoping will be able to help you. Please click here: Ice Maker Not Working. Your expert will also help answer your question. It may take two business days. I do hope that everything works out.

Read More
Marc -
March 10, 2013
A:

my bad. it's model number106.54599400

Read More
Earl -
March 10, 2013
A:

Hi,

Thanks for contacting ManageMyLife. I understand how frustrating it is having trouble with your appliance not working.

Sounds like the icemaker did not dump the ice that was already in the mold.  If the icemaker did work that is fine. But if it did not work, here is some information on your icemaker.  The sensor you can test by opening the freezer door and seeing if the led blink twice.  If so, the sensor is good and the problem is with the icemaker. 

Please feel free to let me know if you need further assistance. We are always here to help.

Thank you for using ManageMyLife.com.

Bill

Read More
Bill__W -
Sears Technician
March 12, 2013
See more answers

Top Parts