Model #10653293202 KENMORE Side-by-Side Refrigerator

  • Cabinet
    3 Results
  • Refrigerator Liner
    3 Results
  • Refrigerator Shelf
    3 Results
  • Freezer Liner
    3 Results
  • Motor And Ice Container
    3 Results
  • Refrigerator Door
    3 Results
  • Freezer Door
    3 Results
  • Dispenser Front
    3 Results
  • Air Flow
    3 Results
  • Control
    3 Results
  • Unit
    3 Results
  • Icemaker
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

The ice maker stopped making ice

A:

Summer is almost here and cold drinks are always on the menu. I think we all get a little frustrated when an appliance we depend on starts acting up on us. I'm sorry to hear that you are having some issues with your ice maker. I did some research at Managemylife website and found an expert answer to a similar question that may help until your expert can respond. I have attached the link below so you can check it out. If you are thinking about scheduling service and have a qualified technician assist you, I have also attached the link to SearsHomeServices. I hope the links below will help you out.

Read More
James -
April 18, 2012
A:

Thank you for your question. I know it can be disappointing when the icemaker stops working. The icemaker in this model can stop working for a few reasons. Some are listed below:

  • The icemaker itself can fail
  • The water valve may not open
  • The optic boards can fail
  • The fill tube can freeze up
  • Freezer temperature not cold enough (should be 0 � 5 degrees)
The blinking led light can be flashing a code that will indicate the problem. If it flashes 2 times pauses and continues this while the door is open, it will be normal and if it stays on continuous, when the flapper door on the left side is held in, it indicates the boards are ok. I�m attaching a chart for the led indicator. When checking this icemaker, tape the little flapper door shut and disconnect power to the refrigerator. To check this icemaker, slide it out, so the front cover can be removed, to access some test terminals. There is a clip located on the back right corner of the icemaker that will need to be removed, to slide the icemaker out. There will be a screw at the bottom of the clip holding it. I�m sending a picture with instructions to remove this clip. With the clip removed, slide the icemaker out and remove the front cover. You will now see the test terminals, which are marked (see picture). Now remove the 3 screws holding the receiver board on the right side pull the board out and disconnect the harness from the board. Place a jumper between the black and black/white wires (see picture). Now use a second jumper and place it between the L � V terminals on the module. Reconnect the power and with both jumpers in place, water should now flow to the icemaker (be prepared to catch water from the fill tube). If water does flow, the icemaker will need to be replaced. If no water flows but you can hear a humming noise, the water valve will need to be replaced. If nothing at all happens, some voltage checks will need to be made. I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further.

If you do not feel confident repairing this problem or doing any voltage checks yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services . If you need more assistance additional details will be helpful.

Safety Notice: Be sure to disconnect the appliance before performing any troubleshooting procedures. If you are not comfortable with doing any voltage checks or repairs that might be recommended, please contact a local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Scott D -
Sears Technician
April 20, 2012
See more answers
Q:

How do I stop particles from coming through my refrigerator water filter?

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner.

Read More
Alina F. -
January 05, 2012
A:

When the filter is replaced, there will be some dark particles (dust) that may come out at first. This is carbon from the filter but should clear out, after purging it with 2 or 3 glasses of water. If the particles remain, the reservoir may need to be replaced. The reservoir part number for this model is #2256126 . You can purchase this at www.SearsPartsDirect.com . I hope this information is helpful. If you have any additional question please reply back to this thread. Thank you for contacting Manage My Life.

Read More
Tammy S -
Sears Technician
January 08, 2012
See more answers
Q:

Cleaning the coils?

A:

Clean the condenser coil as follows:

  1. Turn unit off and unplug the cord.
  2. Remove toe grill (see picture below) from the bottom of refrigerator.
  3. Vacuum the accumulated dust from underneath the refrigerator and the back of the toe grill.
  4. If customer has condenser cleaning brush, brush the coil with the brush and then vacuum again.
  5. Clean toe grill with mild soap and water and put in back in place.
  6. Plug unit back in and reset controls.

Coil Brush makes it easier to reach around coil areas. Brush can be ordered at: Sears Parts Direct

Coil Brush Part# PM14X51

Read More
Maria M. - Personal Solutions Manager -
Sears Technician
June 11, 2009

Top Parts