Model #10652752100 KENMORE Side-by-Side Refrigerator

  • Cabinet
    3 Results
  • Refrigerator Liner
    3 Results
  • Refrigerator Shelf
    3 Results
  • Freezer Liner
    3 Results
  • Motor And Ice Container
    3 Results
  • Refrigerator Door
    3 Results
  • Freezer Door
    3 Results
  • Dispenser Front
    3 Results
  • Air Flow
    3 Results
  • Control
    3 Results
  • Unit
    3 Results
  • Icemaker
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Trying to determine a repair or purchase solution to a refirg/freezer that does not work on either side. 52752100 There are numbers in tiny print preceeding that look like 106, but too small to...

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when there is problems with the refrigerator.
 
Glad to help out.   Im  looking at your Kenmore refrigerator model number 106.52752100.

Most likely you will need just the electrical parts that connect to the compressor.  The "overload,relay, starter".  See the price and the parts on this link -> Overload,relay starter for model 106.52752100.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: www.SearsServiceCrew.com


Please "RESUBMIT YOUR QUESTIONS IF THERE IS ANY OTHER PROBLEMS".
 
Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs.  Thank you for choosing Sears and using our SearsPartsDirect.com.
 

Read More
Larry L -
Sears Technician
May 07, 2014
Q:

Kenmore side by side fridge, how to test diffuser

A:

 Hi,

Thanks for contacting  ManageMyLife. I understand how frustrating it is having trouble with your appliance.

The baffle seems to be faulty.  If the thermistor warms up the board will drive the baffle open using the black wire and the white and black wire.  The white and black act like the neutral and when the baffle is full open the switch will open and this will stop the motor in the open direction.  When the unit gets cold enough the board will use the orange and black white to drive the motor in the opposite direction until the white and black has voltage on it from the switch closing.   On the black and white wire to the black wire when open at s2  you will read 120 volts AC.  In the position it is in right now you could use black 120 volts AC  and have the orange and black removed from the plug and the diffuser pin where the orange and black wire was, it will need to be jumped to neutral or solid white wire.   This will drive the baffle to the closed position. 

Here is the link for a diffuser

 

Please feel free to let me know if you need further assistance. We are always here to help.

Thank you for using ManageMyLife.com.

Bill

Read More
Bill__W -
Sears Technician
August 21, 2013
A:

Hi Bill, thank you very kindly for the reply! I can't quite follow until we get our wire naming convention in sync and the colors right. I use "yellow/red" to refer to a single wire that has yellow as the primary color, red secondary (although I think I understand you to mean white/black when you write "white and black"). The problem is that I don't have any of the colors you mention, except black. I have on my diffuser harness, with diffuser "right side up": yellow/red up, black middle, orange/black down. How do your colors correspond to these? Note: After writing the above I just noticed the schematic (duh!), which helps a lot. But I'm going to leave the note as is because I want to make sure that the wires you refer to are the 3 wires that go to the diffuser. Are they? The schematic agrees with the colors that I have in my unit. Thanks!

Read More
Joseph -
August 21, 2013
A:

Yes the three wire in the diffuser is the one I refer to. The diagram is the guide to follow, I write black and white but the meaning is black/white or orange/black.

Read More
Bill__W -
Sears Technician
August 22, 2013
See more answers
Q:

remove evaporator cover

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner. Have a great day!

Read More
Alina -
August 11, 2012
A:

Thank you for your question. I'm sorry you are having a problem removing the cover. To remove the cover, the bottom will need to be raised slightly to clear the lip of the drain trough. Now pull the bottom of the cover out and then downward slightly to remove it. If the cover will not move, it will probably be due to frost on the backside holding it in place. Try warming the cover with a hair dryer first, to free it from the frost. Be sure to disconnect the power first, before removing the cover. I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further.

Read More
Scott D -
Sears Technician
August 13, 2012
See more answers

Top Parts