Model #10652212104 KENMORE Side-by-Side Refrigerator

  • Cabinet
    3 Results
  • Refrigerator Liner
    3 Results
  • Refrigerator Shelf
    3 Results
  • Freezer Liner
    3 Results
  • Motor And Ice Container
    3 Results
  • Refrigerator Door
    3 Results
  • Freezer Door
    3 Results
  • Dispenser Front
    3 Results
  • Unit
    3 Results
  • Air Flow
    3 Results
  • Control
    3 Results
  • Icemaker
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Drain water line of Kenmore refrigerator for moving and storage

A:

I know this type of information can be very helpful for you to have. While you are waiting for your expert answer, I did some research on your refrigerator. I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life.

Read More
Jackie S -
December 16, 2011
A:

Thank you. Our movers are here today. We tried a few different things, but I think we still have water in the line.

Read More
Tony -
December 16, 2011
A:

You will need to turn the water supply line off & remove it completely from the water inlet valve. Remove the plastic lines from the water inlet valve that go to the holding tank & ice maker. With the lines removed, press in the water pad to release any pressure left in the water valve.

Read More
Joe G. - Personal Solutions Manager -
Sears Technician
December 17, 2011
See more answers
Q:

Where is the water filter??

A:

A refrigerator is definitely something we depend on and when it begins to malfunction it can be a huge inconvenience. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question.

Read More
Barbara H. -
November 04, 2011
A:

Thank you for your question.

I have looked up the model number you have submitted. This model does not have a water filter. Usually installers will put a filter in the water supply line from the house. The image below shows what an inline filter looks like. Look for a filter like that between where the supply line connects to the back of the refrigerator and where it connects to the house plumbing. I hope this is helpful. Please let me know if you need further assistance.

Here is a link to order any parts you need. Sears Parts Direct .

Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
November 05, 2011
A:

Thanks, Mark! I just pulled the fridge out and it doesn't look like the installers put an inline filter in place. I see just one hose that runs from the wall to the back of the fridge. My concern, and the reason why I was originally looking for a new filter, was that the water pressure on the dispensor has always been pretty weak. I'd hoped that replacing a filter might make a difference - clearly that won't be the answer. Is it possible that this is just the flow we're destined to have? Are we kinking the water supply hose somehow?

Read More
Kate -
November 05, 2011
A:

A few things will cause a slow fill out of the dispenser. First, check for a kink in the hose going to the refrigerator. Then look for the shut off valve for the water supply. If the valve looks like the image below. It is most likely the problem. This valve is called a self-piercing saddle valve. You will need to replace that valve with a regular saddle valve. The regular non-piercing saddle valve is the valve pictured in the second image below. This valve requires you to drill a hole into the pipe for it to work. You should be able to purchase this valve at any hardware store. please let me know if you need further assistance. Thank you for using Manage my life. Mark T.

Read More
Mark T -
Sears Technician
November 06, 2011
A:

Sorry here are the images.

Read More
Mark T -
Sears Technician
November 06, 2011
See more answers
Q:

What can be causing this refrigerator to stop running at times?

A:

If the unit is coming back on when you slam the door, it indicates the problem is with either the defrost timer or the cold control (thermostat). The next time it quits running for awhile, instead of slamming the door, try turning the defrost timer knob. It will be located under the control housing (# 6 in picture). If the unit comes back on, the timer # 482493 will have to be replaced. If it still doesn't come on, turn the cold control knob all the way off and on, a couple of times or tap on it. If the unit comes on now, the cold control # 2198202 will have to be replaced. Both of these parts are available at Sears PartsDirect . If you need more assistance, you can resubmit your question with more details

Read More
Scott D -
Sears Technician
August 26, 2009

Top Parts