Model #10651569103 KENMORE Side-by-Side Refrigerator

  • Cabinet
    3 Results
  • Refrigerator Liner
    3 Results
  • Refrigerator Shelf
    3 Results
  • Freezer Liner
    3 Results
  • Motor And Ice Container
    3 Results
  • Refrigerator Door
    3 Results
  • Freezer Door
    3 Results
  • Dispenser Front
    3 Results
  • Air Flow
    3 Results
  • Control
    3 Results
  • Unit
    3 Results
  • Icemaker
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Capacity for model 106.51569103 10651569103 Kenmore Refrigerator

A:

Thank you for choosing Sears Parts Direct. I will be more than happy to help with your refrigerator. Upon researching model 10651569103; I have posted the refrigerator specifications below based on the model number provided.

25.2 cu.ft, Length:2F11.5, Width:3F2.7, 5F11.0, Weight:318lbs.

I trust this information will help you, we appreciate your business thank for choosing Sears.

Read More
CarlosZ -
Sears Technician
August 09, 2015
A:

Thanks for your help. Are there specifications that show what the freezer capacity is and the refrigerator capacity - i.e., breaking down the 25.2 cu ft total capacity? Thanks.

Read More
Brian -
August 10, 2015
See more answers
Q:

no ice tray not filling 10651569103 Kenmore Refrigerator

A:

It can be very frustrating when the ice maker in your refrigerator fails to produce ice. While you are waiting for your expert answer, I did some research on the unit. At this time, I was unable to locate information that would be helpful in regards to your question. Your expert will answer within 24 to 48 hours with detailed information. Thank you for using Manage My Life.

Read More
Julio -
February 14, 2013
A:

Thank you for your question. I know it can be disappointing when the icemaker stops working. The icemaker in this model can stop working for a few reasons. Some are listed below:*The icemaker itself can fail*The water valve may not open*The optic boards can fail*The fill tube can freeze up*Freezer temperature not cold enough (should be 0 – 5 degrees)The blinking led light can be flashing a code that will indicate the problem. If it flashes 2 times pauses and continues this while the door is open, it will be normal and if it stays on continuous, when the flapper door on the left side is held in, it indicates the boards are ok. I’m attaching a chart for the led indicator. When checking this icemaker, tape the little flapper door shut and disconnect power to the refrigerator. To check this icemaker, slide it out, so the front cover can be removed, to access some test terminals. There is a clip located on the back right corner of the icemaker that will need to be removed, to slide the icemaker out. There will be a screw at the bottom of the clip holding it. I’m sending a picture with instructions to remove this clip. With the clip removed, slide the icemaker out and remove the front cover. You will now see the test terminals, which are marked (see picture). Now remove the 3 screws holding the receiver board on the right side pull the board out and disconnect the harness from the board. Place a jumper between the black and black/white wires (see picture). Now use a second jumper and place it between the L – V terminals on the module. Reconnect the power and with both jumpers in place, water should now flow to the icemaker (be prepared to catch water from the fill tube). If water does flow, the icemaker # 2198597 will need to be replaced. If no water flows but you can hear a humming noise, the water valve # W10408179 will need to be replaced. If nothing at all happens, some voltage checks will need to be made. I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further.   If you do not feel confident repairing this problem or doing any voltage checks yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website:  Sears Home Services.

Read More
Scott D -
Sears Technician
February 15, 2013
See more answers
Q:

Refrigerator

A:

Removing or replacing parts is sometimes difficult but is always a good thing to double check to make sure you are doing it correctly. The link down bellow provides great detailed information on the replacement part by an expert. I hope that you also find it informational and helpful just like how i did.

Read More
celene -
March 13, 2011
A:

Insert a flat blade screwdriver into the 2 notches along the bottom edge of the dispenser front and pry them out. Pull the bottom edge of the dispenser front away from the dispenser about 1 1/2 inches and lift it up to release. The dispenser front can hang from the wires while you work on the dispenser.

Be sure to disconnect the power to the refrigerator before removing the dispenser front panel.

Read More
Jimmy K -
Sears Technician
March 14, 2011
See more answers

Top Parts