Model #10651514100 KENMORE Side-by-Side Refrigerator

  • Cabinet
    3 Results
  • Refrigerator Liner
    3 Results
  • Freezer Liner
    3 Results
  • Motor And Ice Container
    3 Results
  • Refrigerator Door
    3 Results
  • Freezer Door
    3 Results
  • Dispenser Front
    3 Results
  • Air Flow
    3 Results
  • Control
    3 Results
  • Unit
    3 Results
  • Icemaker
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Problem with ice maker model 106.51514100 106.51514100

A:

Thank you for choosing Sears Parts Direct. I will be happy to help with your refrigerator. Upon researching model 106.51514100; if the valve is not closing all the way it will leak water into the fill tube. If it closes to late water will stay in there. The valve could need to be replaced.

Thank you for choosing Sears. We appreciate your business. Have a great day.

Read More
Jeff Wallace Jr -
Sears Technician
January 07, 2015
Q:

Does NOT deliver crushed ice

A:

I am sorry that you are having some difficulties with your ice maker and I will be happy to help. I did some research and I was able to find a link that will provide you with some good troubleshooting tips. I hope this helps with your ice dispenser troubles while you wait for your expert response.

Read More
Joseph P. -
August 07, 2012
A:

Hi,

Thank you for your question. It is concerning when the refrigerator is not functioning correctly. In the case of no crushed ice, on the panel board there is the switch, internal and it is used to select or unselect the crushed ice solenoid that is located behind the bracket where the dispenser motor is mounted. You will need to gain access to the dispenser motor and solenoid by removing the ice bucket and taking the bracket loose to access the solenoid and make voltage checks.
Always unplug or de-energize electrical equipment before removing covers or attempting service. Be careful and wear appropriate hand protection when working around sharp metal parts.

Using a volts ohm meter check the two wires in the solenoid connector. When cube is selected, check the white-red wire to the white and there should be 120 volts AC there. If the voltage is there, replace the solenoid. Here is that link to the part, Kenmore Refrigerator Model 106.51514100 .

If you do not find the 120 volts AC to the solenoid, you will need to gain access to the dispenser assembly on the door. Here is a video . Check the blue wire on the ice lever switch to the white wire on the light bulb socket. There should be 120 volts AC there. The next check is the white-red wire to the white on the light bulb socket. If the 120 volts AC is not there replace the complete dispenser front cover. The reason for that is the switch panel is no longer available as a part. Here is the link for the cover, Kenmore Refrigerator Model 106.51514100 .

If this seems to be too much and you would prefer a Sears Home Services technician out to troubleshoot and repair your refrigerator follow the link.

I hope this is helpful. If I may be of further assistance please include more details in a reply to this post.

Read More
Bill__W -
Sears Technician
August 09, 2012
See more answers
Q:

What could cause a strong burning smell to come from the freezer side of my Kenmore refrigerator model 10651514100 after it sat?

A:

I recommend removing the icemaker from the refrigerator and inspecting it. Slide the ice container out and remove the 2 screws holding the icemaker to the freezer wall. Lift the icemaker away from the wall and disconnect the wire harness from the cabinet.

Take the icemaker to the sink and pry the white plastic cover off the front. Inspect it carefully for scorched or burned places.

If you don’t find any thing burned reinstall the icemaker and fill the mold with water. It should dump the ice after 3 hours.

Read More
Jimmy K -
Sears Technician
April 11, 2008

Top Parts