Model #10651264103 KENMORE Side-by-Side Refrigerator

  • Cabinet
    3 Results
  • Refrigerator Liner
    3 Results
  • Refrigerator Shelf
    3 Results
  • Freezer Liner
    3 Results
  • Motor And Ice Container
    3 Results
  • Refrigerator Door
    3 Results
  • Freezer Door
    3 Results
  • Dispenser Front
    3 Results
  • Air Flow
    3 Results
  • Control
    3 Results
  • Unit
    3 Results
  • Icemaker
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

No ice in ice maker

A:

I have been having issues with my Kenmore Coldspot icemaker also. One problem a few months ago was little ice cubes or none at all. After an expensive service call, realized the only problem was I needed a new water filter. Currently having same problems again, but this time I know it is not the water filter, it's almost new.

Read More
Steve -
October 20, 2013
A:

I know that it can be very frustrating to have issues with your ice maker. There are several components that can causes this to happen. These include the fill tube, the ice maker, or the water valve. To check the fill tube to see if it's frozen will require removing the ice maker. Before removing it I suggest manually energizing the valve to see if water will run to the ice maker. To do this first unplug the refrigerator from the wall outlet. Remove the cover from the front of the ice maker to access the module; there will be some test terminals on it. I'm sending a picture of it. With a well insulated jumper place it between terminals L-V. Plug the unit back in and you should get water to the ice maker. If water does run you know the valve and fill tube are ok. If no water flows then you can remove the ice maker to check the fill tube. Removing the ice maker will require taking the 2 screws loose from the top of the ice maker mold and the one under the mold. With it loose you can now disconnect the wire harness and remove the ice maker. Before doing this again unplug the unit from the wall outlet. If the fill tube is frozen the water valve will need to be replaced. If the tube is clear you will need to reinstall the ice maker to put it into a test cycle. To do this again unplug the unit and with the jumper used earlier, place it between terminals T-H, this should cycle the ice maker when you plug the cord back in. If the ice maker starts after a few seconds remove the jumper and watch it cycle. If it fills at the end of the cycle it indicates the ice maker is not starting on its own and will probably need to be replaced. Check the freezer temperature first however because if it gets above 10 degrees the ice maker may not cycle. If you don't feel comfortable doing this yourself, please click on this link to schedule service: Sears Home Services. Click on "Get Started" and follow the directions, click on the red "NEXT" button to continue. I hope this helps. Please feel free to let me know if you need further assistance. We are always here to help. Thank you for using Manage My Life.com.

Read More
AnneJ -
Sears Technician
October 20, 2013
See more answers
Q:

Cubic feet of Refrigerator

A:

I understand that you want to know the cubic feet of your refrigerator. I have found an excellent link that can help you determine the cubic feet of your refrigerator on your own. I attached the link below if you are interested in viewing it on your own while waiting on your response from an expert. I hope this link comes in handy. Have a great day!

Read More
Alina F. -
June 07, 2012
A:

Thank you for your question. It's nice to know the size of your refrigerator. This is a 22 cubic foot refrigerator. I hope this will help you.

Read More
Scott D -
Sears Technician
June 08, 2012
See more answers
Q:

Why won't the ice maker work after replacing the optic boards?

A:

There can still be a problem with the ice maker itself or the water valve. A good check to help determine which one is using some test terminals, on the ice maker module. Remove the front cover on the ice maker to expose the module and you will see some terminals that are marked (I'm sending a picture). Using a well insulated jumper place it between the T-H terminals. Be careful this is a hot (live) test. The ice maker should cycle and fill now. If it does, it indicates the ice maker is not cycling on its own and will need to be replaced.

If it cycles but doesn't fill the water valve is probably defective. Another check for this will be to use the jumper and place it between the L-V terminals. If water still won't flow the water valve is defective or there is a slim chance the wire between the ice maker and the water valve could have a problem. A technician would have to make that check. If you need more assistance you can resubmit your question with more details.

Read More
Scott D -
Sears Technician
March 02, 2009

Top Parts