Model #10651254103 KENMORE Side-by-Side Refrigerator

  • Cabinets
    3 Results
  • Refrigerator Liner
    3 Results
  • Refrigerator Shelf
    3 Results
  • Freezer Liner
    3 Results
  • Motor And Ice Container
    3 Results
  • Refrigerator Door
    3 Results
  • Freezer Door
    3 Results
  • Dispenser Front
    3 Results
  • Air Flow
    3 Results
  • Control
    3 Results
  • Unit
    3 Results
  • Icemaker
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

How do I uninstall icemaker & install new one. 10651254103 Kenmore Refrigerator

A:

Thank you for choosing Sears Parts Direct. I can certainly assist you in locating the instructions to remove and install the ice maker in your refrigerator. I did look into the model number you have provided and I have found information to assist you. 
I have attached the photo to assist you with your repair. 

Let me know if this helps.

You can also visit searpartsdirect.com for parts, diagrams, and repair information.
 
 
If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .


Thank you for your question. Have a great day. 

Read More
Natasha12 -
Sears Technician
June 12, 2014
A:
Natasha12 -
Sears Technician
June 12, 2014
A:

Thanks that worked

Read More
Ron -
June 12, 2014
A:

Thanks that worked

Read More
Ron -
June 12, 2014
A:

You are very welcome. Thank you for choosing searspartsdirect.com. 

Read More
Natasha12 -
Sears Technician
June 12, 2014
See more answers
Q:

water filter holder leaking 10651254103 Kenmore Refrigerator

A:

Thank You for choosing Sears PartsDirect.com. I regret to hear that you are having issues with your fridge and do understand your frustration. Glad to help out. Im looking at your model number 10651254103 first I recommend as well to replace the filter, it is possible that the filter orings are bad. If the drip continues after the filter is replaced you can remove the water tubes from the fittings from the housing, push in on the collars (colored gray and red on the image below) and then pull the water tubes straight out. I recommend that you unplug the refrigerator and shut off the water supply.  Try to remove the water lines and then re-seat them firmly in the housing. After you remove them, you can re-seat them by pushing them back into the fittings. Give them a slight tug and then push them back down to make sure that they are seated properly. See if the water tubes still leak after making sure that they are seated properly in the housing. If they do, then replacing the filter housing (part 2186443) should fix this problem (unless the water tubes are damaged and causing the leak). Check the water tubes for damage before replacing that housing. If the water tubes are okay, I recommend that you replace the housing.  The housing has 2 screws in front holding to the fridge frame and you will need to remove the 1/4 screw that is holding the small metal arm rod to the left of the housing. 

Read More
Sherman_G_Wallace -
Sears Technician
February 19, 2014
A:

Replacing the filter stopped the drips from the filter housing but still had dripping from the water tubes. I gave both a good push into the housing (re-seated them) and drips stopped. I have been puddle free for a month now. Thanks.

Read More
DWIGHT -
February 19, 2014
See more answers
Q:

Ice maker not working?

A:

The ice maker not working can be frustrating. I found some information for you that I am hoping will be able to help you. I am adding the link below to help you with your question while you wait for your expert response. It may take two business days for your expert to respond. I do hope that this will help you out.

Read More
Marc -
January 30, 2013
A:

Thank you for your question. I know it's frustrating when the icemaker stops working. The icemaker in this model can stop working for a few reasons. Some are listed below:

  • The icemaker itself can fail
  • The water valve may not open
  • The optic boards can fail
  • The fill tube can freeze up
  • Freezer temperature not cold enough (should be 0 � 5 degrees)
The blinking led light can be flashing a code that will indicate the problem. If it flashes 2 times pauses and continues this while the door is open, it will be normal and if it stays on continuous, when the flapper door on the left side is held in, it indicates the boards are ok. I�m attaching a chart for the led indicator. When checking this icemaker, tape the little flapper door shut and disconnect power to the refrigerator. To check this icemaker, slide it out, so the front cover can be removed, to access some test terminals. There is a clip located on the back right corner of the icemaker that will need to be removed, to slide the icemaker out. There will be a screw at the bottom of the clip holding it. I�m sending a picture with instructions to remove this clip. With the clip removed, slide the icemaker out and remove the front cover. You will now see the test terminals, which are marked (see picture). Now remove the 3 screws holding the receiver board on the right side pull the board out and disconnect the harness from the board. Place a jumper between the black and black/white wires (see picture). Now use a second jumper and place it between the L � V terminals on the module. Reconnect the power and with both jumpers in place, water should now flow to the icemaker (be prepared to catch water from the fill tube). If water does flow, the icemaker # 2198597 will need to be replaced. If no water flows but you can hear a humming noise, the water valve # W10408180 will need to be replaced. If nothing at all happens, some voltage checks will need to be made. I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further.

If you do not feel confident repairing this problem or doing any voltage checks yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services . If you need more assistance additional details will be helpful.

Safety Notice: Be sure to disconnect the appliance before performing any troubleshooting procedures. If you are not comfortable with doing any voltage checks or repairs that might be recommended, please contact a local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Scott D -
Sears Technician
January 31, 2013
See more answers

Top Parts