Model #10651222100 KENMORE Side-by-Side Refrigerator

  • Cabinet
    3 Results
  • Refrigerator Liner
    3 Results
  • Refrigerator Shelf
    3 Results
  • Freezer Liner
    3 Results
  • Motor And Ice Container
    3 Results
  • Refrigerator Door
    3 Results
  • Freezer Door
    3 Results
  • Dispenser Front
    3 Results
  • Air Flow
    3 Results
  • Control
    3 Results
  • Unit
    3 Results
  • Icemaker
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

kenmore coldspot refridge

A:

I know this type of information can be very helpful for you to have. While you are waiting for your expert answer, I did some research on the unit. I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life.

Read More
Priscilla V -
November 27, 2011
A:

Thank you for your question. This is a 2001 model side by side refrigerator and is 22 cubic feet. I hope this will help you.

Read More
Scott D -
Sears Technician
November 30, 2011
See more answers
Q:

Joey S. replies to turn off lever to ice maker, wait 2 hours, turn back on and watch ejector move. performed this as described but saw no movement in ice maker

A:

Hi, I see that the damage appears to have been done. You can visit our SearsHomeServices.com website for services. I attached the link below. Hope this helps!

Read More
Dezeray S -
July 20, 2010
A:

The ice maker ejector still should have started rotating regardless if the plastic tubing was chewed by a mouse or not. You can force the ice maker into a harvest mode by removing the ice maker cover and jumping terminal T and H with a short piece of insulated jumper wire. See images below. If the ice maker thermostat has failed jumping T and H will cause the ice maker to begin a harvest cycle and if you leave the jumper wire installed long enough (30 seconds) you should feel the heater operating located on the bottom side of the ice maker mold. If the heater works and ejector begins moving, replace the thermostat. The thermostat may just have dirty connections too. NOTE: DO NOT leave the jumper installed. Remove the jumper as soon as you know the heater is working.

Read More
Joey S -
Sears Technician
July 22, 2010
See more answers
Q:

no water going to icemaker in refridgerator

A:

I noticed that someone had asked a similar question to yours with a response from an expert. I have provided the link below. Hope this helps!

Read More
Alina F. -
July 16, 2010
A:

First, make sure the wire bail arm (key#31) on the side of the ice maker is in the Down/ON position. Because during operation the shut off arm may become temporarily stuck in the ice and as the arm pulls free from the ice, it may snap upward with enough force to lock it in the OFF position.

If the arm is in the down position then raise it up to the off position and then wait 2 hours. Two hours later open the freezer door and lower the shut off arm down to the ON position and watch the ice maker ejector fingers (key#23). The ejector should begin to move and rotate very slowly. If you find the ejector rotating all the way around with out opening the water inlet valve (key#10) and adding water then the most likely failure is the water inlet valve. A faulty valve can cause water to slowly seep up into the ice maker fill tube which will cause the water to freeze inside the fill tube (key#2) and cause an ice blockage. You will likely need to remove the ice maker and thaw out the fill tube and replace the water inlet valve.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services

Read More
Joey S -
Sears Technician
July 19, 2010
See more answers

Top Parts