Model #10650792002 KENMORE ELITE Side-by-Side Refrigerator

  • Cabinet
    3 Results
  • Refrigerator Liner
    3 Results
  • Refrigerator Shelf
    3 Results
  • Freezer Liner
    3 Results
  • Motor And Ice Container
    3 Results
  • Refrigerator Door
    3 Results
  • Freezer Door
    3 Results
  • Dispenser Front
    3 Results
  • Air Flow
    3 Results
  • Control
    3 Results
  • Unit
    3 Results
  • Icemaker
    3 Results
Find part by diagram >

Question and Answers

Q:

Upper Fan in Kenmore Coldspot isn't Blowing. 10650792002 Kenmore Elite Side-by-side refrigerator

A:

Thank you for choosing SearsPartsDirect.com. I will be more than happy to assist you. I can understand any frustration you may have experienced with regards to your unit. Let’s see what we can do for you.

A lot of the times when that fan doesn’t turn on then it would have to be replaced. Another check other than the conductivity would be to spin the blade with your figure, if it spins freely then its ok. But again if it doesn’t turn on then it would need to be replaced.

Hope this information has helped you. If you are not comfortable doing this repair you can click here to schedule a technician or call toll free 1-800-469-4663. Again, thank you for choosing SearsPartsDirect.com.

 

Read More
Samantha A -
Sears Technician
October 21, 2014
Q:

I have a Kenmore refrigerator from 2000 (model no., 10650792002) It is spilling water all over the inside of the freezer door from somewhere in the ice maker.

A:

When the kitchen appliances begin malfunctioning it can be confusing. I was able to locate two similar questions that may help while you wait for the expert to review this model. I attached the links below. I hope this helps.

Read More
Priscilla V -
May 23, 2012
A:

Thank you for your question. I can understand your concern about the water leak. This could be a problem with the icemaker itself or the water valve. This icemaker has some test terminals behind the front cover, that may help determine the cause of this problem. Pull the front cover off and you will see the terminals. Now, use a well insulated jumper and place it between the T & H terminals (see image). Be careful this is a hot (live) check. The icemaker should now start into a cycle and after approx. 12 seconds, remove the jumper. Toward the end of the cycle, it will fill with water. This should be a 7.5 second fill time. If the fill time is 7.5 seconds and if the water overfills the icemaker, the water valve # W10408179 will need to be replaced. If the fill time is longer then 7.5 seconds, there is an adjustment on the icemaker to reduce the fill time (see second image). If the fill time is still too long, the icemaker # 2198597 will need to be replaced. I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Scott D -
Sears Technician
May 24, 2012
See more answers
Q:

water fill tube

A:

When it comes to replacing parts on your appliances owner's manuals are the best thing to have in hand. While you are waiting on an expert to answer your question, I took some time to search your model number and found your owner's manual. I have attached the link below. Hope this helps!

Read More
Dezeray S -
March 14, 2012
A:

Thank you for your question. I'm sorry you have this problem with the fill tube. This can be a difficult tube to replace and a technician may be needed. This tube has to be pulled out from the front. If it broke off and you cannot get hold of the remaining section of tube, a technician will be needed. If there is enough to hold, first make sure the tube is completely free of ice. Hot water may need to be forced up in the tube to clear it. When the tube is clear, take the water line loose behind the cabinet and have someone push on the tube, while pulling it out from the front, at the same time. The new tube will push back in from the front. I hope this will help you. If you would like more assistance, reply to this thread and I will assist you further.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Scott D -
Sears Technician
March 15, 2012
See more answers

Top Parts