Model #10650782001 KENMORE Side-by-Side Refrigerator

  • Cabinet
    3 Results
  • Refrigerator Liner
    3 Results
  • Refrigerator Shelf
    3 Results
  • Freezer Liner
    3 Results
  • Motor And Ice Container
    3 Results
  • Refrigerator Door
    3 Results
  • Freezer Door
    3 Results
  • Dispenser Front
    3 Results
  • Air Flow
    3 Results
  • Controls
    3 Results
  • Unit
    3 Results
  • Icemaker
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

What typically needs replacing when the ice maker stops working?

A:

I can understand your concern over wanting to know what usually needs to be replaced when the ice maker in your refrigerator fails. While you are waiting for your expert answer, I did some research on the unit. At this time, I was unable to locate information that would be helpful in regards to your question. Some of these questions that are asked will need specific research and will be answered by an expert with-in two business days but usually sooner.

Read More
Julio -
March 23, 2013
A:

Thank you for your question. I know it can be disappointing when the icemaker stops working. The icemaker in this model can stop working for a few reasons. Some are listed below:*The icemaker itself can fail*The water valve may not open*The optic boards can fail*The fill tube can freeze up*Freezer temperature not cold enough (should be 0 – 5 degrees)The blinking led light can be flashing a code that will indicate the problem. If it flashes 2 times pauses and continues this while the door is open, it will be normal and if it stays on continuous, when the flapper door on the left side is held in, it indicates the boards are ok. I’m attaching a chart for the led indicator. When checking this icemaker, tape the little flapper door shut and disconnect power to the refrigerator. To check this icemaker, slide it out, so the front cover can be removed, to access some test terminals. There is a clip located on the back right corner of the icemaker that will need to be removed, to slide the icemaker out. There will be a screw at the bottom of the clip holding it. I’m sending a picture with instructions to remove this clip. With the clip removed, slide the icemaker out and remove the front cover. You will now see the test terminals, which are marked (see picture). Now remove the 3 screws holding the receiver board on the right side pull the board out and disconnect the harness from the board. Place a jumper between the black and black/white wires (see picture). Now use a second jumper and place it between the L – V terminals on the module. Reconnect the power and with both jumpers in place, water should now flow to the icemaker (be prepared to catch water from the fill tube). If water does flow, the icemaker # 2198597 will need to be replaced. If no water flows but you can hear a humming noise, the water valve # W10408179 will need to be replaced. If nothing at all happens, some voltage checks will need to be made. I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further.   If you do not feel confident repairing this problem or doing any voltage checks yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services.  If you need more assistance additional details will be helpful.  _Safety Notice_: Be sure to disconnect the appliance before performing any troubleshooting procedures. If you are not comfortable with doing any voltage checks or repairs that might be recommended, please contact a local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.  

Read More
Scott D -
Sears Technician
March 25, 2013
See more answers
Q:

why do I have water leaking from the back of the water filter cartridge on my kenmore coldspot refrigerator model number 10650782001

A:

I'm sorry to hear that you are having some difficulties with your water filter. I did some research for you at Managemylife.com and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. I hope these links provided assist you.

Read More
Joseph P. -
October 29, 2011
A:

Thank you for your question. I can understand your concern about this water leak. This type of water leak will usually be from the water line connections on the back of the filter. First, try disconnecting the water lines and cutting the ends off, if there is enough tubing. I'm attaching a picture with instructions of how these fittings work. Reinsert the tubes all the way and then if they still leak, the filter housing # 2186443 will need to be replaced. It's available at SearsPartsDirect . I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further.

Read More
Scott D -
Sears Technician
November 01, 2011
See more answers
Q:

What is the cu ft capacity of each side of Model 106.50782001 AND the exact dimensions?

A:

In regards to your Kenmore refrigerator, Model # 106.50782001

In ordered to get the proper dimension of your refrigerator it will have to be self measured. After the refrigerator is measured you can multiply the depth times the width of each section which will provide you with the cubic feet of the refrigerator. You can always provide your model number to your appliance representative who can recommend a similar model refrigerator.

Read More
Angela R. - Personal Solutions Manager -
Sears Technician
June 17, 2009

Top Parts