Model #10650594000 KENMORE ELITE Side-by-Side Refrigerator

  • Cabinet
    3 Results
  • Refrigerator Liner
    3 Results
  • Refrigerator Shelf
    3 Results
  • Freezer Liner
    3 Results
  • Motor And Ice Container
    3 Results
  • Refrigerator Door
    3 Results
  • Freezer Door
    3 Results
  • Dispenser Front
    3 Results
  • Air Flow
    3 Results
  • Controls
    3 Results
  • Unit
    3 Results
  • Icemaker
    3 Results
Find part by diagram >

Question and Answers

Q:

Ice maker on off switch 10650594000

A:

Based on your symptoms, the sending and receiving control boards on the walls of the freezer are bad. There is a kit that has both boards. The kit is part number 4389102. Replacing both of those control boards using that kit should fix your problem. Be sure that you unplug the refrigerator before accessing internal components and replacing parts.

 

If you need more help, let us know. 

Read More
Lyle W -
Sears Technician
November 19, 2013
Q:

where is water valve 10650594000 Kenmore Elite Side-by-side refrigerator

A:

Thank you for choosing SearsPartsDirect.com. I understand how important it is to be able to replace the water valve in your refrigerator. The valve is located behind your refrigerator and may be hidden with a back access panel.
I have included instructions below on how to replace the water valve.
SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

1. Pull the refrigerator away from the wall so that the rear is accessible.

2. Unplug the power cord from the wall outlet and turn off the water supply valve by turning the handle clockwise until it is tight.

3. Remove the water supply line from the water inlet valve using an adjustable wrench. Place a towel below the valve to catch any water remaining in the line.

4. Remove the lower access panel of the refrigerator by removing the screws securing it in place.

5. Remove the mounting screws securing the inlet valve to the refrigerator cabinet.

6. Transfer the solenoid wire connectors from the old inlet valve to the new inlet valve.

7. Press each quick-connector on the bottom of the inlet valve, at the point at which the each tube enters the inlet valve using an open-ended wrench. Measure 11/16 of an inch from the end of the tube and make a mark using a marker. Insert the tube into the same tube inlet on the new inlet valve up to the mark. Repeat for each tube.

8. Secure the new inlet valve the to refrigerator cabinet using the mounting screw removed from the old valve.

9. Replace the lower access panel of the refrigerator.

10. Connect the water supply line to the new inlet valve. Tighten the compression nut using and adjustable wrench.

11. Turn on the water supply valve and examine the connection for any leaks. Tighten as necessary.

12. Plug the refrigerator's power cord back into the wall outlet and then push the refrigerator back against the wall.

13. Run approximately one gallon of water through the water fountain to clear air from the tubes.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services
If you have further questions please let me know. Thanks for using SearsPartsDirect.com.

Read More
Lokelani -
Sears Technician
August 25, 2013
Q:

icemaker not making ice

A:

It's an inconvenience to have problems with the ice maker. I found a link that shows how to test your ice maker to determine what the problem could be. I provided the link below. An expert will respond with additional information. Hope this helps!

Read More
Yadira B -
September 03, 2012
A:

Thanks for your question about the Kenmore ice maker problem. I know how frustrating this can be, I will be happy to assist. Because there is no ice being dumped, is there any ice in mold but just has not dumped. If there is nothing in mold and the tube has no ice blocking then yes the inlet valve could be defective.( if you are getting water through door then it�s not clogged.) I see that Yadira offered a link and this link will be helpful. I suggest you do the testing of ice maker before you decide to replace valve. If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Thanks Ron H.

Read More
Ron H -
Sears Technician
September 05, 2012
See more answers

Top Parts