Model #10644439600 KENMORE ELITE Side-by-Side Refrigerator

  • Cabinet Parts
    3 Results
  • Refrigerator Liner Parts
    3 Results
  • Refrigerator Shelf Parts
    3 Results
  • Freezer Liner Parts
    3 Results
  • Motor And Ice Container Parts
    3 Results
  • Refrigerator Door Parts
    3 Results
  • Freezer Door Parts
    3 Results
  • Dispenser Front Parts
    3 Results
  • Air Flow Parts
    3 Results
  • Control Parts
    3 Results
  • Unit Parts
    3 Results
  • Icemaker Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Question and Answers

Q:

leaky refrigerator water dispenser 10644439600 Kenmore Elite Side by side refrigerator

A:

Thank you for contacting Sears. I will be more than happy to assist you with your Kenmore refrigerator.

I can understand the frustration of your dispenser not functioning properly, after researching model number 106.44439600. When the dispenser is leaking its likely due to either the water filter or the water valve. I would suggest definitely replacing the water filter first if you haven’t in the past 6 months. After this is done there’s a good chance the water valve is not closing properly allowing it to continue to run causing the drip at the dispenser.

I hope you found this information useful. Again thank you for choosing Sears. We appreciate your business, have a great day.

*Safety disclaimer before you try and repair the unit make sure the power supply is disconnected. There may be sharp parts to the unit that can cause injury to you if not careful. If you don’t not feel comfortable checking this yourself you can request a technician by visiting www.SearsHomeService.com*

Read More
Benny23 -
Sears Technician
July 27, 2015
Q:

Side by side model 106-44439600

A:

I can appreciate your need for instruction to gain access to your refrigerators drip pan.  I was able to locate instructions on a unit with a similar model number.   Click here to view the link.  Though this link discusses a different model number,
the mechanics are likely going to be very similar. Keep in mind that an expert will be
responding within the next two business days if not sooner and will likely offer you more information and
instruction. I hope this information will be helpful and have a nice day.

Read More
Henry -
June 25, 2013
A:

Thanks for contacting ManageMyLife.com. John, I know how important it is to have information on your refrigerator. I see Henry did a great job in finding a similar question and unit that will help you above. Click here to view that answer. I hope this helps.

Please feel free to let me know if you need further assistance.

Thank you for using ManageMyLife.com.

Read More
Jonathan B -
Sears Technician
June 25, 2013
See more answers
Q:

Icemaker bin latch jammed

A:

Its amazing how much we depend on our appliances. Having issues with the icemaker I'm sure is frustating. I did some research and found an expert answer that may assist you until your expert responds. I attached the link below.

Read More
James -
November 30, 2010
A:

I apologize for not answering sooner. The problem with the ice dispenser is probably caused by air leaking through the flapper door in the dispenser. The moisture in the air freezes the ice bin to the door liner and make it very difficult to remove.

I suggest you go to http://services.sears.com/shs/category/repair?sid=MMLxexpertxmerch and get a Sears technician to remove the ice bin from the door and repair any other problem that would cause the ice bin to freeze again.

If you need to get the ice bin off now, use a hair dryer and warm the ice bin enough to release it from the door. Be careful not to melt the ice bin or the door liner.

Read More
Jimmy K -
Sears Technician
November 30, 2010
See more answers
Q:

icemaker stopped working

A:

Having a Refrigerator with ice maker is a great appliance to have but when it starts to have problems it can get very frustrating. While you are waiting on an expert to answer your question, I found a great link in the Manage My Life website on why Ice Maker isn't working. I attached the link below. Hope this helps!

Read More
Dezeray S -
November 29, 2010
A:

I know it's frustrating when the icemaker stops working. The icemaker in this model can stop working for a few reasons. Some are listed below:

  • The icemaker itself can fail
  • The water valve may not open
  • The optic boards can fail
  • The fill tube can freeze up
  • Freezer temperature not cold enough
The blinking led light can be flashing a code that will indicate the problem. If it flashes 2 times pauses and continues this while the door is open, it�s normal. Now disconnect power to the refrigerator. To check this icemaker, slide it out, so the front cover can be removed, to access some test terminals. There is a clip located on the back right corner of the icemaker that will need to be removed, to slide the icemaker out. There will be a screw at the bottom of the clip holding it. I�m sending a picture with instructions to remove this clip. With the clip removed, slide the icemaker out and remove the front cover. You will now see the test terminals, which are marked (see picture). Now remove the 3 screws holding the receiver board on the right side and disconnect the harness from the board. Place a jumper between the black and black/white wires (see picture). Now use a second jumper and place it between the L � V terminals on the module. Reconnect the power and with both jumpers in place, water should now flow to the icemaker (be prepared to catch water from the fill tube). If water does flow, the icemaker # 2198597 will need to be replaced. If no water flows but you can hear a humming noise, the water valve # W10247725 will need to be replaced. If nothing at all happens, some voltage checks will need to be made. I hope this will help you. If you would like more assistance, additional details will be helpful and I will be glad to assist you further.

If you do not feel confident repairing this problem or doing any voltage checks yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services . If you need more assistance additional details will be needed.

Safety Notice: Be sure to disconnect the appliance before performing any troubleshooting procedures. If you are not comfortable with doing any voltage checks or repairs that might be recommended, please contact a local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Scott D -
Sears Technician
November 30, 2010
See more answers
Q:

How do I put the drawers back in my refrigerator?

A:

To remove the drawers in the refrigerator section, slide the drawer out until it stops. Lift slightly on the handle of the drawer and slide it forward. This will cause it to slide over the built in stop on the rails.

To reinstall the drawer lift the front of the drawer while sliding the back into the rails on either side. This will let the drawer slide back over built in stop on the rails. Push the drawer in until it seats in the front.

If you require further assistance please resubmit question with more details. I will be looking forward to helping you again in the near future.

Read More
Landell -
Sears Technician
January 26, 2010
Q:

I have a Sears fridge model 10644439600, 2 years old. How do we store it? What to do when restarting?

A:

Store the refrigerator in an upright position. Put some packing in the refrigerator and freezer to prevent the doors from closing. This will prevent mold and mildew from forming inside the cabinet. Clean and dry the interior of the refrigerator and freezer before storing.

If the refrigerator will be exposed to below freezing temperatures you must drain the coil of tubing located behind the crisper drawers. Disconnect the tubing from the water valve and drain as much water out of the water valve as possible. Be sure the tubing that goes from the water valve to the icemaker is disconnected and allowed to drain.

You don't need to do anything before starting the refrigerator. Plug it in and turn it on, it should be fine.

Read More
Jimmy K -
Sears Technician
September 25, 2008

Top Parts