Model #105A YORX Misc Audio

  • No Image Available - Fidelitone
    3 Results
Find part by diagram >

Question and Answers

Q:

How do I test for a blocked drain line? LRFD21855ST

A:

Thank you for choosing Sears Parts Direct. I will be happy to help with refrigerator. Upon researching model LRFD21855ST; the drain hose can be tested. When it freezes you can use warm to hot water from the faucet. Look at the bottom of the drain line under the refrigerator. When the water starts flowing underneath then the tube has been defrosted. After it defrosts I recommend spraying compressed air to clear the tube of any debris or left over ice. It might take a couple cups of water before it defrosts. Having a wet/dry vacuum will make it easier to vacuum any excess water. I can’t see a reason why the drain tube would have to be replaced unless it’s damaged. I posted a link below and the drain tube is number 105a.

Thank you for choosing Sears. We appreciate your business. Have a great day.    

Read More
Jeff Wallace Jr -
Sears Technician
November 18, 2014
Q:

How do I test for a blocked drain line? LRFD21855ST

A:

Thank you for choosing Sears Parts Direct. I will be happy to help with refrigerator. Upon researching model LRFD21855ST; the drain hose can be tested. When it freezes you can use warm to hot water from the faucet. Look at the bottom of the drain line under the refrigerator. When the water starts flowing underneath then the tube has been defrosted. After it defrosts I recommend spraying compressed air to clear the tube of any debris or left over ice. It might take a couple cups of water before it defrosts. Having a wet/dry vacuum will make it easier to vacuum any excess water. I can’t see a reason why the drain tube would have to be replaced unless it’s damaged. I posted a link below and the drain tube is number 105a.

Thank you for choosing Sears. We appreciate your business. Have a great day.    

Read More
Jeff Wallace Jr -
Sears Technician
November 18, 2014
A:

Thank you for choosing Sears Parts Direct. I will be happy to help with refrigerator. Upon researching model LRFD21855ST; the drain hose can be tested. When it freezes you can use warm to hot water from the faucet. Look at the bottom of the drain line under the refrigerator. When the water starts flowing underneath then the tube has been defrosted. After it defrosts I recommend spraying compressed air to clear the tube of any debris or left over ice. It might take a couple cups of water before it defrosts. Having a wet/dry vacuum will make it easier to vacuum any excess water. I can’t see a reason why the drain tube would have to be replaced unless it’s damaged. I posted a link below and the drain tube is number 105a.

Thank you for choosing Sears. We appreciate your business. Have a great day.    

Read More
Jeff Wallace Jr -
Sears Technician
November 18, 2014
See more answers
Q:

5600 Watt Generator will run only on full choke.

A:

I know how disappointing it is when you are unable to properly use your generator. I researched your question and was unable to find any information that would be helpful. An expert will respond shortly. It usually takes 24-48 hours to receive a response. Have a good day.

Read More
Jackie S -
August 05, 2012
A:

Thank you for your question.



I am sorry you are having a problem with the generator. I searched for a video that shows how to clean the carburetor you have. I did not have any luck finding a video. Usually when the engine will only run on full choke it is because the main jet is partly plugged. I posted an image below that shows where the main jet is. Click on the image to enlarge it. Once you have the main jet removed, clean the holes out with a tip cleaner and carburetor cleaner. The second image below shows what a tip cleaner looks like. Find the biggest one that will fit into the jet and work it in and out. Then flush the hole with carburetor cleaner. Do this in all the holes you see. Then reassemble the carburetor and check the operation. _NOTE:_ If the fuel in the tank is older than five weeks old it should be drained out. Then refill the tank with fresh fuel.


If you need further assistance, please reply below with more details. Thank you for using Manage my life.

Mark T.

Read More
Mark T -
Sears Technician
August 06, 2012
A:

Mark Looking at the diagram, it looks similar to the entire float assembly I have here. The bowl pictured has a screw in the bottom where my bowl is mounted with two screws on the side and the float/main jet assembly are "one piece" where the main float is removed by removing the pin and exposing the jet pin. I will pull it again and clean it as noted. The second image was not present, only the first one pointing out the main jet. Thanks for the reply, Mark

Read More
John -
August 06, 2012
A:

John,

I am sorry the last image did not load. I reposted it below. The second image should be closer to your model. I marked the main jet in the image. Once it is apart, clean the jet with the tip cleaner and carburetor cleaner. You should be able to pick up the tip cleaner at your local Sears store.
Please let me know if you need further assistance.
Thank you for using Manage my life. Mark T.

Read More
Mark T -
Sears Technician
August 07, 2012
A:

Crisis averted. Cleaned the center port of the float assembly (main jet) and I am back in business. Engine runs as it was designed. Thanks Mark, for your assistance. Received a survey and will reply with a very positive thumbs up.

Read More
John -
August 11, 2012
A:

Mark T -On the issue of 5600 Watt Generator will run only on full choke. You said, I posted an image below that shows where the main jet is. Click on the image to enlarge it. Once you have the main jet removed, clean the holes out with a tip cleaner and carburetor cleaner. The second image below shows what a tip cleaner looks like. Find the biggest one that will fit into the jet and work it in and out. Then flush the hole with carburetor cleaner. I don't see the images you refer you, please repost.

Read More
Jeffrey -
September 20, 2013
A:

The images Mark T. posted are on his second post. When you drop the bowl, there is a pin holding the float assy. Remove that pin and remove the float assemble. Be very careful lowering it down. There is a pin (labled as 105A) on the diagram that will come down with it. Once all of that is down and out of the way, you will see the jet in the center. Use the tip cleaner to clean the port. If you don't have a tip cleaner handy, I was able to use one of the larger paper clips in my desk drawer, inserting and removing it in the port and then following it with carburetor cleaner and I was back in business. When I initially inspected it, the port was almost completely closed up, with an almost shell like appearance over the hole. So simple to do, re-assembled everything back as it was and was back up and running. Hope this helps. John

Read More
John -
September 22, 2013
A:

Jeffrey I think you are viewing this question on our partsdirect site. For some reason the images are not showing up there. I recommend pasting the following link in your browser. http://www.managemylife.com/mmh/questions/312149-5600-watt-generator-run-full-choke I hope this is helpful. Please let me know if it does not work.

Read More
Mark T -
Sears Technician
September 25, 2013
See more answers