Model #1035 JENN-AIR Ranges, Electric

  • Basic Assemblies & Loose Parts
    3 Results
  • Door
    3 Results
  • Controls Group
    3 Results
  • Body
    3 Results
Find part by diagram >

Question and Answers


The "clean" light continually blinks and dishwasher will not run 66517019401 Kenmore Dishwasher


Thank you for choosing and being a valued member.  I can certainly understand how frustrating it can be when your dishwasher is not working properly.

Usually when your clean light is blinking, it does mean that there is a heating malfunction.  If it blinks 7 times then there is a heater fault. 

If a temperature rise in the water is not detected during the first 8 minutes of the beginning of the main wash, the dishwasher will shut down.

A fault will be indicated if:
A 2°F increase in the water temperature is not obtained (inlet water temp greater than 90°F) or
A 4°F increase in the water temperature is not obtained (inlet water temp less than 90°F).
If the correct temperature rise is not detected, the dishwasher will drain and blink the clean light
7 times to signal to the consumer to call for service. The detection will be ignored if the temperature is out of its normal range 64 - 160° F or the door is opened during the first 8 minutes of the main wash. This is to prevent a false detection.

Heater circuit problem:
? Open in heater.
? Open connection or component in heater circuit.
? Faulty heater drive circuit on control

1. Unplug dishwasher or disconnect power.
2. Check all components and connections in
the water heating circuit or heat dry circuit.
? Check resistance of heater.
? Check resistances of all connections and
components between the control and
? Check operation of heater and temperature
sensor in Diagnostics cycle.

The heating element can be tested by disconnecting the electrical wire connections from the heating element and testing the resistance of the heater using an ohm meter. NOTE: Disconnect or remove power to the dishwasher before servicing the dishwasher. The heating element should have a resistance of 10-35 ohms.

At room temperature the thermistor should show between 11k to 12k ohms.

You will see the thermostat with an orange & a white/red wire connected to it. Remove the thermostat bracket and test the thermostat. You'll want to get an ohms reading of zero. 
661566 is the replacement part number. 

You can also visit for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Natasha12 -
Sears Technician
June 08, 2015

Fire hazard 665.15953000


Thank you for being Sears’ valued member and for contacting with your question the replacement heater element for your Kenmore dishwasher model 665.15953000. I understand your concern about replacing only what is needed to repair your dishwasher and not paying for extra parts. I will be happy to help you with this.
I have reviewed the parts list for your dishwasher and it appears the original part number was 8268559. Based on information we received from the manufacturer, the heating element should be replaced if it is open and not operating, or if a continuity test on the element doesn’t read between 10-35 Ohms. If the element needs to be replaced, you must review the serial number of the dishwasher and whether it has a plastic or stainless steel tub.

Your dishwasher has a stainless steel tub. If the serial number on it is FR34 to present, the replacement element number is 8537057. If your dishwasher has a serial number from FK30-FR33, you will need to replacement element kit number 8194200, which is the element and the control. On the dishwashers that require this kit, it is because the higher wattage of the new heating element requires the use of the control. The control will pulse the element on and off during operation. Because of the increased wattage, you may notice shorter dry cycles, shorter wash cycles and changes in the times displayed (if you have a display model).  

SAFETY WARNING: Disconnect the power supply before beginning your repair to prevent the risk of electrical shock which can result in property damage, serious personal injury or even death. If you are not comfortable completing this repair, you can set up service at or by calling 1-800-469-4663 (1-800-4MY-HOME). 

I hope this answers your question. Thank you for choosing Sears, we appreciate your business. 

Read More
Rachel Morgan -
Sears Technician
April 04, 2015

Thank you for the prompt repsonse. My dishwasher serial is FL351496, so I figure it falls into the "FK30-FR33" range... is this right? I understand tha the 8194200 kit offers an upgrade from the original arrangement, but I am very satisfied with this dishwasher's performance and do not feel I need a more powerfull heating element. Please confirm that the part W10518394 is a direct replacement for the original heating element 8268559 and that it will give me the same performance as before the element broke. If not, could you give me the equivalent number that will work with the original arrangement, i.e. the current board. Thank you for all your help and have a great day.

Read More
s -
April 07, 2015
See more answers

Washer Not Progressing Through Cycle 66516889000 Kenmore Dishwasher


Hello, glad to help.  Thank You for choosing Sears
I am sorry and do understand your frustration when there is problems with the dishwasher not going through the cycle.
Glad to help out.  I’m looking at your Kenmore Dishwasher model number 66516889000.

All I have read and experience states it most likely is a heating problem with the light on and not cleaning well.  The heating element fails and does not heat the water adequately clean nor dry the dishes.  

Replace the heating element if it is open and not operating, or perform a continuity test on the heating element and replace if rading is not between 10-35 ohms.
Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs.  Thank you for choosing Sears and using our

Read More
Larry Jr -
Sears Technician
August 04, 2014