Model #1033248091 KENMORE Range (gas)

  • Burner Section
    3 Results
  • Body Section
    3 Results
  • Visi-bake Upper Oven And Lower Broiler Door
    3 Results
  • Full Glass Upper Oven And Lower Broiler Door
    3 Results
  • Control Panel Section
    3 Results
  • Wire Harness And Components
    3 Results
  • Filter Kit
    3 Results
Find part by diagram >

Question and Answers

Q:

Is the igniter supposed to shut off? 1033248091 Kenmore Kenmore gas built-in oven

A:

 Hi,

Thanks for contacting  ManageMyLife.  I understand how frustrating it is having trouble with your appliance.

Yes, after the flame is going in the burner and the knob is released the igniter should become inactive.    

 

 

Be careful and wear appropriate hand protection when working around sharp metal parts.

 

 

Please feel free to let me know if you need further assistance. We are always here to help.

Thank you for using ManageMyLife.com.

Bill

Read More
Bill__W -
Sears Technician
September 20, 2013
Q:

Kenmore wall oven Model #103.324 891.

A:

When an oven is not operating as it should it is a huge inconvenience when it comes to making a home cooked meal. I was able to find a couple links that might help you diagnose you oven. I attached the links below. I hope this helps.

Read More
Jackie S -
March 22, 2012
A:

Thank you for your question and I understand your concern.

I was not able to pull up any information by the model number provided. You may have mis-read the model number. Without having a valid model number I can only provide general information.

The information I found on the models I listed below does not have a freestanding pilot flame.

  • 103.3248010
  • 103.3248091
  • 103.3248092
  • 103.3248210
  • 103.3248290
  • 103.3248291

These models I listed above uses a glow bar igniter to ignite the burner. The igniter must receive voltage from the oven thermostat in order to glow red. It must glow red and it must pull enough current/amperage to cause the oven safety valve to open. If the glow bar igniter is not glowing, it could have a faulty/broken igniter, a faulty oven safety valve or oven thermostat.

Also, if the Start knob on the clock has been pushed it, the oven will not come on. See images below.

The igniter and thermostat is likely available but not the oven safety valve. Based on the age of the wall oven you may want to think about replacing the oven.

So that's what I can tell you at this point. I can give you more detailed help if you could provide me with a valid model number. If you could supply me with that information I will be happy to assist you further if needed.

Read More
Joey S -
Sears Technician
March 23, 2012
See more answers
Q:

how do I replace the ignition on my kitchen aide oven kgst300hbl6

A:

I have provided you with a couple links that may assist you with replacing the ignition on your oven. An expert will respond shortly to give you a detailed answer specific to your model. I do hope these links help you with your repair. http://www.managemylife.com/mmh/questions/151933-where-can-i-find-instructions-on-how-to-replace-the-igniter-on-a-kenmore-pilot-free-ignition-oven-model-1033248091 http://www.managemylife.com/mmh/questions/221106-access-wiring-replace-oven-ignition-device-kenmore-model-79077471793-parts-1

Read More
Jacqueline S -
November 07, 2010
A:

The procedure for replacing the igniter in this KitchenAid range will be slightly different than most other ranges. I provided the illustrated procedure in the image below. Your range may look slightly different than the one shown below but the basic procedure should be the same. Be sure that you shut off the circuit breaker to the range and close the gas supply shut-off valve before beginning this process.

If you need more help, reply with additional details and we will assist you further.

NOTE: If you have not already ordered the igniter, you can buy it from the Sears PartsDirect website. The part number is 9782065.

Read More
Lyle W -
Sears Technician
November 08, 2010
See more answers