Model #10305 SNAPPER Snowthrower, Gas

  • Augers, Impeller
    3 Results
  • Discharge Chute
    3 Results
  • Collector Housing
    3 Results
  • Belts/idler/drive Plate/sheave
    3 Results
  • Gearbox, Shafts
    3 Results
  • Frame, Traction Drive
    3 Results
  • Chain Case (traction Drive)
    3 Results
  • Handles, Controls (8242)
    3 Results
  • Handles, Controls
    3 Results
  • Engines/pulley/idler
    3 Results
  • Wheels, Hub
    3 Results
  • Decals
    3 Results
  • Decals (continued)
    3 Results
  • Decals (continued)
    3 Results
  • Accessories
    3 Results
  • Accessories
    3 Results
Find part by diagram >

Question and Answers

Q:

cleaning my kenmore oven

A:

Error codes can mean so many different things so when an error code comes up it can be really frustrating. While you are waiting on an expert to answer your question, I found a great link in the Manage My Life website. I have attached the link below. Hope this helps!

Read More
Dezeray -
April 03, 2013
A:

Hello Nat. I am sorry to hear about that problem you are having with your Kenmore Wall Oven Model 911.47089.

 

Trying to self clean the oven by using the method you are describing will normally not attain the same results as the self clean cycle. The self clean cycle uses a much higher temperature to burn off spills and residue inside the oven cavity in a controlled manner. That is why the oven door remains locked during that self cleaning cycle. Opening the oven door during a cleaning cycle would result in a sudden influx of oxygen. That can result in a fire inside the oven cavity. The normal bake or broil mode will not heat the oven cavity to a sufficient temperature for cleaning. 

 

The F1 that you encounter after the self clean cycle indicates that you have a problem with the keypad or the electronic control board in the console.  The technical explanation of that code is shown in the image below. Based on your details, you could have a problem with the door lock relay on the control board. Your details seem to indicate that the F1 code eventually clears so that you can use the oven again. To fix this problem, you will probably need to replace the electronic oven control board (part WB27T10305). You can order that part from this page: Oven Control Board for Kenmore Wall Oven Model 911.47089. Shut off the house circuit breakers for the oven to completely disconnect electrical power before accessing internal components and replacing parts. You should be able to release the console and access the control board by opening the oven door and removing the screws at the bottom of the control panel. You can then lift up on the control panel and fold it forward.

 

I hope that this information helps. If you need more assistance, reply with additional details.

 

 

If you get to the point where you need to have a service technician examine and repair the oven, you can schedule service through this link: Sears Home Services Oven Repair. 

 

Read More
Lyle W -
Sears Technician
April 04, 2013
See more answers
Q:

I need to order GE microwave JE1590SC01 Part#WB27X10305 magnetron; this is for my mother's microwave which is in the Philippines but purchased in San Francisco

A:

I can understand you have a certain amount of time to get the megatron for the GE microwave. Just click on the link provided below and type in the part number. Hope this helps while waiting for additional information from an expert.

Read More
Anna T -
January 30, 2013
A:

I understand needing to order the magnetron for your mother's microwave. I see Anna provided you with some excellent information. The magnetron can be ordered from Sears Parts Direct. However, because microwaves are extremely dangerous to service, a technician will be required to order it from Parts Direct.

Microwaves contain high-voltage components that can retain a lethal electrical charge of up to 2200 VAC -- even when the microwave is unplugged. Repairs and adjustments, even minor ones such as replacing fuses, can cause microwave leakage. A microwave shielding leakage test MUST be performed after any microwave service . I do not recommend attempting to install the unit yourself.

The part number is manufacture issued. This means you can take the part number and check other parts sites for customer availability.

I really hope this information helps you today. Thank you for using ManageMyLife.com.

Read More
Korinna S -
Sears Technician
January 30, 2013
See more answers
Q:

Kenmore Cannister Vacuum 116.28014700 will not turn off without unplugging. The Control Unit appears to shut off (all lights go out) but vacuum remains runnin

A:

I know how important your vacuum is to you when your cleaning your home. I researched your question and found a link with information specific to your model. I attached the link below. I hope this helps.

Read More
Jackie S -
February 20, 2012
A:

I suspect the switch in the handle has failed. You will need to replace the power control in the handle. It cost approximately $66 dollars. I assume when the handle is removed the vacuum shuts off. The information may be helpful to you in completing this project. Remember to unplug the unit first. If you do not feel confident repairing this problem yourself, then you can have it repaired by a Sears technician. Here is a link that will provide the nearest drop-off locations: Sears Home Services .

Read More
Fred M -
Sears Technician
February 21, 2012
A:

I was thinking the power control board as well. I had another reference to an older post with the same problem suggesting it was suction motor control in the cannister. (KC96PDDVZC0E for about $42.00). Any thoughts from Fred on this??

Read More
Lachlan -
February 21, 2012
A:

One way to be sure is to disconnect the 3 wire connector shown in the image below. If the unit still runs then replace the PCB "A" board. If it doesn't run then replace the PCB "B" board.

Read More
Fred M -
Sears Technician
February 22, 2012
A:

And Please remember to unplug the unit first.

Read More
Fred M -
Sears Technician
February 22, 2012
A:

Fred, I am appreciating your help. Double checking before I order. I am using the parts diagram from Kenmore. I unplug CN4 and still runs. I unplug CN1 and it doesn't run - this looks like the power supply to the cannister. It looks like I need to get a whole new control board which includes A and B - part 10 on my diagram which is the Power Control Board PART NUMBER: KC89VDDUZ000 which is listed for $103.05. Does this sound correct?

Read More
Lachlan -
February 23, 2012
A:

That would be correct.

Read More
Fred M -
Sears Technician
February 25, 2012
See more answers