Model #10269 CRAFTSMAN Workbench / Project

  • Unit
    3 Results
Find part by diagram >

Question and Answers

Q:

My oven will not heat up 91195879790 Kenmore 30" radiant electric range

A:

Thank you for submitting your question. I understand your concern and I will be happy to assist you. The issue you're experiencing could be with the oven temperature probe (WB21X5301) or the main control board (WB27T10269). The images below will assist you with accessing and testing the temperature probe. You'll need an ohms/volt meter to test the temperature probe. The probe should measure around 1100 ohms at room temperature (+/- 10%). If the resistance of that probe is bad, it will need to be replaced. I was also able to find a video on this process. If the temperature probe test good, then replce the main control board. You can order parts from our Sears Parts Direct web site. I hope this helps. Please reply back to this thread if you require further assistance. Thank you for using Manage My Life.

Read More
Tykara -
Sears Technician
October 07, 2013
Q:

Stove is giving error message

A:

Error codes can be an inconvenience and keep the range from working properly. I did some research and I was able to find a link that will provide you with some good information. I hope this helps with your range error code troubles while you wait for your expert response.

Read More
Joseph P. -
August 20, 2012
A:

Thank you for submitting your question. The F2 error code indicates the oven temperature has exceeded 590 degrees with the door unlocked or 990 degrees with the door locked. The electronic range control (ERC) senses the oven temperature by the resistance of the oven temperature sensor. As the temperature goes up the resistance of the sensor increases and the ERC converts the resistance to degrees. Sometimes the sensor fails and gives high or low resistance readings. Sometimes the ERC fails and calculates the temperature wrong. Sometimes a relay on the ERC sticks and the temperature goes too high. Sometimes there is a bad connection between the sensor and the ERC causing high resistance and the ERC thinks the temperature has gone too high. The most likely issue will be with the oven temperature sensor which needs replacing. If you have a volt/ohm meter you can check the sensor resistance to see if it is in calibration. It should read 1100 ohms at 75 degrees. The oven temperature sensor is part number WB21X5301 priced at $74.12. You can order parts from our Sears Parts Direct web site.Here's a video . If the sensor test okay, then issue will be with the main control board (WB27T10269) and that will need to be replaced. If you do not feel comfortable performing test or repairing this problem yourself, I recommend scheduling for service. You can schedule for service online with our Sears Home Services team. I hope this helps. Please reply back to this thread if you require further assistance with this repair. Thank you for using Manage My Life.

Read More
Tykara -
Sears Technician
August 22, 2012
See more answers
Q:

are stove parts interchangeable?

A:

I know this type of information can be very helpful for you to have. While you are waiting for your expert answer, I did some research on the unit. I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life.

Read More
aashe -
November 21, 2011
A:

The information that I have on those control boards indicates that they are not compatible. I do not recommend that you try to replace the control board WB27X5562 with the WB27X10269. You can send that control board WB27X5562 to a company called Core Centric Solutions to have it repaired. Be sure that you unplug the range or shut off the house circuit breaker to disconnect power before accessing internal components and removing that control board. Here is a website that has contact information for that control board repair company: CoreCentricSolutions.com . The cost of a control board repair is normally around $150. This would be a better solution than trying to replace that control board with a different part that appears to be incompatible.

If you need more help, let us know.

Read More
Lyle W -
Sears Technician
November 23, 2011
See more answers