Model #1000 FITNESS QUEST Weight System

  • Total Gym 1000
    3 Results
Find part by diagram >

Question and Answers

Q:

WHEELS ON UPPER RACK BREAK OFF 66512773K310 Kenmore Elite Dishwasher

A:

Thank you for being Sears’ valued member and for contacting SearsPartsDirect.com with your question about the upper rack wheels for your Kenmore Elite dishwasher model 66512773K310. I am so sorry the plastic prongs are breaking. I will be happy to help you with this. In this case you will need to replace the assembly. The replacement kit includes both the left and right assemblies and all the parts to install them. It is important to replace both sides. The kit will include installation instructions. I have included the link below for you to order the replacement kit for the parts. 
SAFETY WARNING: Disconnect the power supply before beginning your repair to prevent the risk of electrical shock which can result in property damage, serious personal injury or even death. If you are not comfortable completing this repair, you can set up service at www.SearsHomeServices.com or by calling 1-800-469-4663 (1-800-4MY-HOME). 

I hope this answers your question. Thank you for choosing Sears, we appreciate your business. 
 

Read More
Rachel Morgan -
Sears Technician
May 16, 2017
A:

Thank you for your response to our question! We had already consulted the parts list and have ordered the parts you recommended. i am glad to know the new parts should be sturdier than the ones that have broken.

Read More
SUSAN -
March 11, 2015
A:

I am having this exact same problem. It started with one wheel and now three wheel tabs have broken. My dishwasher is just at two years as well. It is very frustrating!

Read More
Michael -
August 13, 2015
A:

My top rack just fell out and I found both the front and rear wheels have broken plastic tabs. My dishwasher is only two years old! I bought this brand/model because Consumer Reports rated it well. It is unacceptable to me that a part that gets so much use is made of cheap plastic. I shouldn't have to buy two new assemblies at $40+ each. Same problem as other customers have noted. This is a manufacturing defect!

Read More
Monika -
September 13, 2015
A:

Three of the plastic wheel holders are broken. Machine is 2 years old: this is DEFINITELY a manufacturing defect. Warranty out 1 year, I demand a better response than "buy the better part'.... how about "We'll ship that to you for free sir." I'll be writing to Consumer Reports on this one.

Read More
PiTa -
September 17, 2015
A:

three of the plastic wheel holders are broken. machine is 2 years old: this is definitely a manufacturing defect found parts cheaper at http://www.repairclinic.com/PartDetail/b6p9/Kenmore-Dishwasher-Rack-Adjuster/W10712394/3447661?ss=a9b6d1417455-x773130373132333934&mr=1

Read More
Alesha Jans -
October 23, 2015
A:

Mine are also all broken and the top rack fell out. The replacement parts are $40 each. I paid over $1000 for this dishwasher; defective parts should be replaced by Sears for a 2 year old appliance, This is unacceptable! I was going to buy my daughter one like mine for Christmas. Now I believe I will go to Lowe's and get a Samsung.

Read More
karen -
November 22, 2015
See more answers
Q:

Kenmore Gas Grill, 146.16132110.

A:

You can think of a searing station as an extra burner. It is use for searing meat prior to cooking. Searing locks in the juices and browns the meat. If you use it as an extra burner, make sure you turn down the flame before using.

Read More
Henry -
September 30, 2012
A:

Hello Richard,

I would like to answer your question and assist you. The searing burner is a super hot burner for searing meat to seal in the meat juices. To use the burner turn it on and wait about 5 minutes for it to heat up. Use a little oil on the grate or directly coat the meat lightly prior to putting it on the searing burner, to prevent it from sticking.

Lay the meat on the grill and wait only about 2 minutes and rotate the meat a half turn to get the grill marks pattern on the meat. Depending on the thickness of the meat you will only have to wait a couple more minutes before you flip the meat over and repeat the procedure. You can continue to cook the meat on the searing burner if you can turn it down on your model or move it off the searing area to a cooler part of the grill and continue cooking until you have the desired doneness you like. Let the meat stand for about 5 minutes loosely covered with foil to let the meat juices move back into the meat before you cut or serve.

Please let me know if you would like any further assistance.

Jerry C

Read More
Jerry C -
Sears Technician
October 01, 2012
A:

No bad jerry. i have an all-infrared grill that's very hot all the time. the sear burners can be adjusted but there is only so much range. The thing to remember with infrared burners is heat is direct off the flame. With a traditional "blue-flame" bbq burner the closed hood causes heat to build-up and surround the food with hot air. An infrared burner direct-heats the food above it. This is very different. For instance, even if you could close the hood of a blue-flame bbq and build up to 1200 degrees this would not be the same as an infrared grill because the infrared heat is not conducted in air or radiated off briquettes. The only difference I would suggest from jerry's message above is to move the steak/fish/burgers every 10 - 15 seconds for the first minute of searing. Using oil will interrupt your dry rub or marinade. A cooking grate makes a huge differential in heat because of the direct heat of an infrared burner. it is possible to have strips in the meat of cooked and raw meat because of the grates. I have posted a lot if images showing this on our blog. instead of using oil to stop sticking move the food very slightly -- about the space of a single space of a grid or quarter-turn the food every 15 seconds. This will give the food a better sear and stop sticking. A better sear means the outer layer f food is sealed so moisture cannot drip. lots of flavor when cooked this way. Also, an experienced grilling tip for infrared amazement: use marinade then dry rub then a good tenderizer with razors. Pack the flavor in the steak and sear fast above 1000 degrees and you'll never be able to justify spending eighty dollars on a fancy steak again!

Read More
grillrepair -
December 01, 2012
A:

I would love to write a scathing review on this grill. I bought it three years ago brand new from SEARS. After one year, I had to replace the drip pan because it rotted out. Now after 3 years, everything inside the grill has corroded beyond function. I always kept it covered when not in use. I've owned a lot of grills in my life but this was the biggest POS I have ever had.

Read More
SCOTT -
January 12, 2016
See more answers
Q:

Radial Arm Saw Recall ? 113199250 Craftsman Craftsman 10-inch radial saw

A:

Thank you for being Sears' valued member; and thank you for contacting SearsPartsDirect.com with your questions about the recall on your Craftsman 10-inch Radial Saw model 113199250. I am so sorry your saw was affected by the recall. For assistance with your options under a recall, please contact our Recall Customer Care department at 1-800-659-7026. To ensure you are given all of your options, I will defer to our Customer Care advisors' expertise. If I can be of further assistance, please let me know.  Thanks you for choosing Sears, we appreciate your business. 

Read More
Rachel Morgan -
Sears Technician
September 29, 2014
A:

Hello, I also have this radial saw model, can I also contact recall customer care department at 1-800-659-7026? Is isn't to late to get help with this issue is it?

Read More
Gilbert -
May 26, 2015
A:

I just found out this saw was recalled, and was mad as hell since I had also never seen the recall on the Sears site, only through word of mouth some 20+ years on. I lost the end of my index finger due to this very problem, and since I registered my product (a long, long time agao at purchase, I have never been notifieed of a recall and only found this thanks to someone pointing i out in a forum. The fact is, the $100 check is a rebate check and a joke if you suffered an injury like I did. I just sent off my 3rd email about this, as my saw is in near mint condition and has been well cared for. I only found the recall last week by pure accident, even though I registered my product like I do with all my tools. The kick in the teeth is that to even find workable parts, the price tag runs well over $600 as far as I can tell, and if the parts are not available, a new saw like this is between $1000-$1500. Instead of a check for a measly $100, how about covering the cost of a new finger tip Sears? Do they even understand the pain, loss and work issues a guy goes through after something like this? And at the time, they basically skirted the issue and made me feel like I had been the one at fault. Not cool.

Read More
David -
December 21, 2015
A:

Craftsman 10"radial saw MN 113.197751 I just found out this saw was recalled, and was mad as hell since I had also never seen the recall on the Sears site, only through word of mouth some 20+ years on. I lost the end of my index finger due to this very problem, and since I registered my product (a long, long time agao at purchase, I have never been notifieed of a recall and only found this thanks to someone pointing i out in a forum. The fact is, the $100 check is a rebate check and a joke if you suffered an injury like I did. I just sent off my 3rd email about this, as my saw is in near mint condition and has been well cared for. I only found the recall last week by pure accident, even though I registered my product like I do with all my tools. The kick in the teeth is that to even find workable parts, the price tag runs well over $600 as far as I can tell, and if the parts are not available, a new saw like this is between $1000-$1500. Instead of a check for a measly $100, how about covering the cost of a new finger-tip Sears?

Read More
David -
December 21, 2015
See more answers