Model #10 SCHWINN Cycle

  • Cycle
    3 Results
Find part by diagram >

Question and Answers

Q:

Why do I get a F10 error code on a Kenmore Elite stove?

A:

The F10 indicates that the electronic oven control board senses a runaway temperature condition in the oven through the oven sensor circuit. Oven temperature is detected by the control board as it monitors the resistance through the oven temperature sensor circuit. You could have a failed oven temperature sensor, a wiring harness failure, an open thermal switch or a failed electronic oven control board that would cause this problem. The first component to check would normally be the oven temperature sensor probe. If you have a volt/ohm meter, you can shut off the breaker for the range and remove the screws that mount this sensor to the back wall of the oven. Carefully pull the wire harness into the oven cavity until you get to the wire harness disconnect plug. You should have enough slack to pull it this far into the oven. Disconnect the sensor but do not let the wire harness retract back through the back wall of the oven or it will be hard to reconnect. Measure the resistance of the oven temperature sensor with your volt/ohm meter. At room temperature, the resistance should measure around 1100 ohms. The resistance chart is shown in the image below.

If the resistance is above 2200 ohms at room temperature, then the sensor probe is causing the F10 error code and will need to be replaced.

You can order a new sensor probe from the Sears PartsDirect website. The part number for the sensor is 316217002.

If the resistance is normal, then one of the other causes mentioned above is producing your F10 code. You would need to access the electronic oven control board in the console and check the resistance at the sensor circuit connection to the control board as the next step in troubleshooting this problem if sensor resistance is normal. If you need more help with this problem, resubmit your question with additional details.

Read More
Korinna S -
Sears Technician
April 27, 2010
Q:

Kenmore washer 417.44052400 will not spin in the spin cycle.

A:

Thank you for your question.  I am sorry about the spin problem on your Kenmore 417.44052400 Front Load Washer.   If the washer is tumbling in both directions in the wash cycle then the motor is okay.  If the water drains out but the washer does not spin then the usual suspect is the door lock assembly.  The door must be locked for the washer to spin.  The simple test is to run the diaganostic test.  The instructions are in the image below.  If the washe spins in the test then the door latch assembly should be replaced.  If it does not spin then there is another problem.  Try the test and see what happens.  You can reply below with any additional details for further assistance.    The do-it-yourself is possible but dealing with the door boot can be frustrating.   The 2nd image will give you an idea.  You can also have the problem repaired in your home by a Sear technician.  Here is the link: Sears Home Services Washer Repair.   I hope this information helps.  Thank you for using Manage My Life. 

Read More
Fred M -
Sears Technician
August 28, 2013
A:

Fred, Your help was right on the button!! My wife (very non-technical) was able to perform the door latch test and inform me that the door latch was the problem. I picked up a new one on the way home and 10 later we had a fixed washer. Thanks, Jon

Read More
noodl -
September 05, 2013
A:

Glad to help and congratulations on a great self repair.

Read More
Fred M -
Sears Technician
September 08, 2013
A:

I am having this same problem, how do I run a diagnostic test? I also have an additional question does this model have a filter? I am asking because a ring went through the wash awhile back and was never found..Any ideas? Thanks

Read More
Jamey -
September 10, 2013
A:

Jamey, the instructions to run the test are shown in the image below. This particular washer does not have a filter but there is a hose from tub to pump you may want to check for the ring. The 2nd image below may be helpful fo you.

Read More
Fred M -
Sears Technician
September 15, 2013
A:

Hello everyone Having the same problem and before I could try the door latch test my father just cut the wire to bypass the door latch. Dont ask me but we still are having the the no spin thing happening. Looking for help please and thank u

Read More
Anthony -
September 25, 2013
A:

Anthony, By passing the door switch is not possible on this model. The control must see the door switch open and close or it will assume there is a door switch error. There is also a door lock circuit. If there is no spin but the washer will tumble in wash then the motor and speed control are likely okay. If the washer will spin in test mode then replacing the door lock assembly will most likely correct the problem.

Read More
Fred M -
Sears Technician
September 29, 2013
A:

Hello, I have the same problem. Can I get the instructions also? Thanks

Read More
CHRIS -
August 15, 2015
A:

I'd like to run the door lock assembly diagnostic test, but I can't seem to expand the image of the test sufficiently to read it. Please help.

Read More
Anonymous -
November 30, 2015
A:

Same model front load washer, replaced the control board but it will not tumble or spin. Help

Read More
joaquin -
February 02, 2016
See more answers
Q:

Vacuum agitator brush wont turn. There is no problem with the suction at all there is no belt to fix and there doesn't seem to be anything hung in it.

A:

These are great cleaners. I own one and have had this problem before. Check page 21 and reset the agitator overload. If it still does not run, you might want to check the previous expert post below on how to access the brush area to look for an obstruction. I attached both these links below. Hope this helps get your vacuum cleaning again.

Read More
Barbara H. -
December 10, 2010
A:

Thank you for your question.

Not having the roller brush running can be a concern.

You are right this model does not use a belt to drive the brush; it has a direct drive motor internal to the brush.

There are a few things we can check to see why it is not operating.

  • First check the reset button on the top of the base unit. It may have tripped. Push to reset.

Before disassemble please REMOVE POWER from the vacuum.

  • If that is set then we will need to remove the 10 screws at the bottom of the base by turning the unit over and locating and removing all ten screws and then lift off the base assembly.

I have sent some pictures that illustrate the diagnostic and disassemble procedures.

  • If you have a Volt/Ohm meter you can check for continuity resistance in the motor circuit.

  • Set your meter to the RX1 ohm scale and check the thermal overload which is the flat reed like piece on top of the motor. This motor runs on 170 volts DC.

  • Check the continuity across the motor brushes.

  • Check the continuity across the overload protector.

If all these checks are ok it will indicate that the PCB board that powers the brush motor is bad and it is located up in the dust box suction motor housing.

This is a difficult place to get to so I would suggest at this point you take the unit in to be serviced.

If you do not feel confident repairing this problem yourself, then you can have it repaired by a Sears technician. Here is a link that will provide the nearest drop-off locations: [Sears Home Services | http://services.sears.com/shs/category/repair?sid=MMLxexpertxmerch

If you would like to continue with disassemble of this unit please use the link for further instructions.

I hope this will help.

Thank you for using Manage My Life.

Read More
Sam A -
Sears Technician
December 11, 2010
A:

My vacuum does the same thing, except it has no suction.

Read More
Janet -
December 18, 2011
A:

Thank you Janet; for your question on the vacuum cleaner. If you have the exact same model then I would say if the suction motor is not working you may have a problem with the motor control board. Please send me your model number information and a little more detail on your specific model. Sam A.

Read More
Sam A -
Sears Technician
December 19, 2011
A:

Sam, the model # is 11635923500, and serial # is M63443626. Thank you!

Read More
Janet -
December 20, 2011
A:

Thank you for the model number for the upright vacuum cleaner. If the suction motor is running then I would suggest removing the hose from the connector pipe down by the nozzle and make the hose and the pipe that gets the dirt from the roller brush are clear. If the motor is not running there could be a couple of reasons. The switch on the handle could be bad and need replacing, or the motor controller circuit board may have failed or the thermal fuse in line with the motor may have opened and last is if the motor burned out. Please tell me if the motor is running and you have no suction or if the suction motor is not running. If you select the bare floor mode it will turn the roller brush motor off and the suction motor should be the only motor on. Please let me know what you find out and we can continue to troubleshoot. Sam A.

Read More
Sam A -
Sears Technician
December 20, 2011
A:

Hello, The agitator on our model 11625615500 is jammed. On of the end caps on the agitator itself will not rotate. Is there a way to remove this part or will I have to replace the whole agitator assembly?

Read More
Greg -
May 22, 2013
A:

Here is the Kenmore Power-mate model for this unit: 11655615500.

Read More
Greg -
May 22, 2013
A:

Hi I have model 11635922500. There does not appear to be any obstructions, but it does not feel like the brush is turning properly. I am not getting any suction. However if I use the utilities, I do get suction. Any suggestions?

Read More
Justin -
July 20, 2013
A:

Hi Justin and Greg, sorry no one has responded to your questions.

Greg, on your model I'm showing the end caps only come with a new agitator assembly. The end caps are not sold separately. Here is the link to PartsDirect for the complete agitator.

Agitator Assembly for Model 116.55615500

Justin, I recommend taking the agitator off and trying to turn the motor shaft by hand. If you have trouble turning it by hand then the problem may be with the motor. The motor is a non-serviciable part, you will need to replace it. If the shaft turns fine the check the two end caps on the agitator to make sure they are turning okay.

Motor Assmebly for Model 116.35922500

If you have further questions please let me know.
Thanks for using ManageMyLife.com

Read More
Desirea -
Sears Technician
September 05, 2013
See more answers